Lavor CRYSTAL CLEAN Instrucciones Para El Uso página 9

- Press button 1 (fig.1) to start the brush
rotating.
- Press button 2b boiler switch 2b (fig.1) (TO
WASH WITH HOT WATER). Hot water will
be on temperature after few seconds.
- Press button 2 (fig.1) to deliver water or
detergent solution, setting the dosage to
suit the type of surface and the type of dirt
and trying not to use more than necessary.
- Press button 3 (fig.1) to suck up dirt water
and detergent solution applied to the floor.
- Move the machine slowly forward and
back, following a washing pattern as shown
in figure 9 if possible.
- Keep using the rotating brush in the
most difficult points to remove the most
stubborn dirt.
WARNING
- Before starting to wash the floor, users are
advised to try out the machine on a small
area to check whether the detergent about
to be used is suitable for the surface to be
cleaned and to perfect the method of use.
- Do not leave the machine stationary with
the rotating brush on. This might damage
the floor.
- The detergent solution dosage must ensure
that the squeegee blades do not work dry.
MAINTENANCE
AFTER WORK
- After disconnecting the plug from the
mains socket, wind the lead around the
hooks provided (fig.2) and move the
machine's handle to the vertical position,
until the pedal catch is heard.
- Empty both the tanks and rinse and dry
them carefully.
- Return the tanks to the handle and place
the machine in a protected place, where
it is not at risk of knocks, frost, humidity
or water. The machine must be placed on
the stand provided to avoid damaging the
squeegee blades (fig.10).
CLEANING THE BRUSH
- With the aid of a screwdriver, unscrew the 2
screws shown in fig.11.
- Free the brush by taking hold of it from
the side of the 2 screws just removed and
extract if from the pin on the opposite side
- Clean the brush under running water,
taking care to dry it perfectly before
putting it back in place.
- To reconnect the brush, turn the drive pin
to the position shown in fig.12.
- Place the brush on the drive pin.
- Bring the bearing towards its seat.
- Turn the brush by hand while free to
position the bearing correctly.
- Re-close by tightening the 2 screws, taking
care not to trap the bristles of the brush.
CLEANING THE SQUEEGEE BLADES
- To remove the squeegee blades, they must
be separated by releasing the retainers at
the ends (fig.13) and extracting them in
opposite directions (fig.14)
- Clean them under running water with the
aid of a non-aggressive detergent and
insert them in the guides, remembering to
re-engage the end retainers.
TROUBLESHOOTING
THE BRUSH DOES NOT TURN
- Check that the plug is connected to the
mains socket.
- Check that the switch is pressed correctly..
- If you are using a power lead extension,
make sure that it complies with the
minimum dimensions stated in the safety
precautions section.
- The brush motor has
overheated: check that the air intakes in the
base have not become blocked and wait for
the overload cutout to reset.
- Check that there are no jammed objects
preventing the brush from rotation
- If the problem persists contact the nearest
Service Centre
THE MACHINE DOES
DETERGENT
- Check that there is detergent in the tank
- The tank has not been fitted correctly
and the delivery valve is not working.
Reposition the tank.
- After removing the brush, clean the 4
detergent delivery nozzles with the pin
provided (fig.15)
- If the problem persists contact the nearest
Service Centre
THE MACHINE DOES NOT DRY
- Check that the suction squeegee blades
are properly positioned and that their
end retainers are closed (see maintenance
section) (fig.13).
- Empty the dirty detergent collection tank.
- Check that the hoses are connected (figs.16
and 17) and not bent at an acute angle
(fig.18).
- Check the wear of the pattern on the
squeegee blades (fig.19). If necessary
replace them, referring to the maintenance
section.
- Check the wear of the pattern on the
squeegee blades (fig.19). If necessary
replace them, referring to the maintenance
section.
- If the problem persists contact the nearest
Service Centre
THE MACHINE DOES NOT CLEAN PROPERLY
- Check that the brush and the squeegee
blades have been fixed correctly (see
maintenance section).
- Check the brush for wear (the min. bristle
length is 20mm). If necessary replace them,
referring to the maintenance section.
- If the problem persists contact the nearest
Service Centre
EXCESSIVE FOAM PRODUCTION
- Too much detergent in the water.
- If the problem persists contact the nearest
Service Centre
THE DETERGENT SOLUTION IS NOT EVENLY
DISTRIBUTED
- After removing the brush, clean the 4
detergent delivery nozzles with the pin
provided (fig.15)
- If the problem persists contact the nearest
Service Centre
THE MACHINE LEAKS WATER
- Empty the dirty detergent collection tank
(fig.8).
- Check that the O-ring seal is present and
undamaged (fig.20)
- If the problem persists contact the nearest
Service Centre
WARRANTY
All our appliances have undergone thorough
checks and are covered by a 12-month
warranty against manufacturing defects.
The warranty period starts from the date of
accidentally
purchase. If the machine is repaired during
the warranty period, a copy of the purchase
document must be enclosed.
The warranty is only valid if:
- The defects are of material or manufacturing
(defects which cannot be clearly attributed
to the material or manufacture will be
examined by one of our technical service
NOT DELIVER
centres or on our premises, and the charges
will be allocated depending on the results).
- The instructions in this manual have been
followed to the letter.
- The repairs have been carried out by
authorised repairers.
- The machine has not been subjected to
overloads such as knocks, dropping or
frost.
- Suitable detergents have always been
used.
The warranty does not cover:
- Parts subject to normal wear and tear
(brush, squeegee blades, paintwork).
- Accidental
transport, damage due to negligence or
improper treatment, or damage due to use
or maintenance not in accordance with the
instructions provided in the this instruction
manual.
- The cleaning of functional parts.
A repair under warranty includes the
replacement
of faulty parts, while shipment and packaging
are not included. Any replacement of the
appliance and extension of the warranty
further to work done on defects is not
possible. The repair is carried out at one
of our authorised technical service centres
or on our premises and the machine must
reach us freight prepaid, i.e. with freight costs
paid by the user. The manufacturer declines
any liability for any injury or damage caused
by poor installation or imperfect use of the
appliance.
As the owner of electrical or electronic
equipment, the law (in accordance with
the EU Directive 2012/19/EU on waste from
electrical and electronic equipment and the
national laws of the EU Member States that
have implemented this Directive) prohibits you
from disposing of this product or its electrical /
electronic accessories as municipal solid waste
and obliges you to make use of the appropriate
waste collection facilities.The product can be
disposed of by returning it to the distributor
when a new product is purchased. The new
product must be equivalent to that being
disposed of. Disposing of the product in the
environment can cause great harm to the
environment itself and human health.
The symbol in the figure indicates the urban
waste containers and it is strictly prohibited to
dispose of the equipment in these containers.
Non-compliance
spulated in the Directive 2012/19/EU and
the decrees implemented in the various EU
Member States is administratively punishable.
damage, damage
DISPOSAL
with the regulationtis
EN
during
9