Safety Notes; Functional Description; Intended Use - stayer MULTI L20 Manual De Instrucciones

gb

1. SAFETY NOTES

SAFETY NOTES SAFETY WARNINGS FOR
PRECISION SAW
- Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring. Cutting
accessory contacting a "live" wire may make exposed
metal parts of the power tool "live" and could give the
operator an electric shock.
- Use the machine only for dry sanding. Penetration
of water into the machine increases the risk of an
electric shock.
- Keep hands away from the sawing range. Do not
reach under the workpiece. Contact with the saw
blade can lead to injuries.
- Use suitable detectors to determine if utility lines
are hidden in the work area or call the local utility
company for assistance. Contact with electric lines
can lead to fire and electric shock. Damaging a gas line
can lead to explosion. Penetrating a water line causes
property damage or may cause an electric shock.
- When working with the machine, always hold it
firmly with both hands and provide for a secure
stance. The power tool is guided more secure with
both hands.
- Secure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure than
by hand.
- Keep your workplace clean. Blends of materials are
particularly dangerous. Dust from light alloys can burn
or explode.
- Never use the machine with a damaged cable. Do
not touch the damaged cable and pull the mains
plug when the cable is damaged while working.
Damaged cables increase the risk of an electric shock.
- Wear protective gloves when changing application
tools/accessories. Application tools/accessories
become hot after prolonged usage.
- Do not scrape wetted materials (e. g. wallpaper)
or on moist surfaces. Penetration of water into the
machine increases the risk of an electric shock.
- Do not treat the surface to be worked with solvent-
containing fluids. Materials being warmed up by the
scraping can cause toxic vapours to develop.
- Exercise extreme caution when handling the
scraper. The accessory is very sharp; danger of injury.
BATTERIES USE AND CARE
Do not open the battery. Danger of short-circuiting.
Protect the battery against heat, e. g., against continuous
intense sunlight, fire, water, and moisture. Danger of
explosion.
In case of damage and improper use of the battery,
vapours may be emitted. Provide for fresh air and seek
medical help in case of complaints. The vapours can
irritate the respiratory system.
Use the battery only in conjunction with your STAYER
power tool. This measure alone protects the battery
against dangerous overload.
Use only original STAYER batteries with the voltage
listed on the nameplate of your power tool.
When using other batteries, e. g. imitations,
reconditioned batteries or other brands, there is danger
of injury as well as property damage through exploding
batteries.
Do not continue to press the On/Off switch after the
machine has been automatically switched off. The
battery can be damaged.
The battery is equipped with a temperature control
which allows charging only within a temperature range
of between 0 °C and 45 °C. A long battery service life is
achieved in this manner.
Observe the notes for disposal.
Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the
lithium ion battery of your power tool.
The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in
the battery charger before using your power tool for the
first time.
The lithium-ion battery can be charged at any time
without reducing its service life. Interrupting the charging
procedure does not damage the battery.
The lithium-ion battery is protected against deep
discharging. When the battery is empty, the machine is
switched off by means of a protective circuit: The
inserted tool no longer rotates.
Temperature Dependent Overload Protection
When using as intended for, the power tool cannot
be subject to overload. When the load is too high or
the allowable battery temperature range of 0–50 °C is
exceeded, the speed is reduced. The power tool will
not run at full speed until reaching the allowable battery
temperature. position. Unintentional actuation of the On/
Off switch can lead to injuries.
Open the keyless chuck 2 by turning in rotation direction,
until the tool can be inserted. Insert the tool. Firmly
tighten the collar of the keyless chuck 2 by hand in
rotation direction . This automatically locks the drill
chuck.
The locking is released again to remove the tool when
the collar is turned in the opposite direction.

2. FUNCTIONAL DESCRIPTION

Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result
in electric shock, fire and/or serious injury.
While reading the operating instructions, unfold the
graphics page for the machine and leave it open.

INTENDED USE

The machine is intended for sawing and cutting wooden
materials, plastic, gypsum, non-ferrous metals and
fastening elements (e.g., unhardened nails, staples). It is
also suitable for working soft wall tiles, as well as for dry
sanding and scraping of small surfaces. It is especially
suitable for working close to edges and for flush
cutting. Operate the power tool exclusively with Stayer
accessories.
- 20 -