Disposing Of The Battery - Telwin pro start 2212 Manual De Instrucciones

metal part of the engine; do not connect the clamp to
the negative terminal of the battery.
If the warning light comes on (Fig. A-1) and
the buzzer sounds this means "REVERSE
POLARITY", DANGER!
In these circumstances NEVER switch on the vehicle,
and remove the cables immediately!
Make sure the vehicle battery and starter battery
polarities are correct before making the connections
described above.
- If there is no acoustic warning signal and the red light
is OFF, the battery charge status LED (Fig. A-2) will
come on to indicate that the internal automatic switch
has triggered the starter function. The starter clamps
are now powered up.
- Turn the ignition switch or key of the vehicle or boat to
ON. Wait about one minute. Turn the vehicle ignition to
the start position for no more than 3÷4 seconds. If the
vehicle or boat does not start, wait at least 3 minutes
before trying again.
activated, do not allow the black and red
clamps to come into contact with each other
or to touch a common conductor.
instructions below with great care:
1. Disconnect the black (negative) clamp from the
vehicle.
2. Disconnect the red (positive) clamp from the vehicle.
3. Return the clamps to their housing.
It is highly recommended to recharge the starter as soon
as possible.
- Take the cover off the cigar-lighter type socket (Fig.
A-3).
- Insert the cigar-lighter plug of the device to be powered
into the socket (Fig. A-3).
- Raise the USB port cover (Fig. A-4).
- Insert the USB cable of the device to be powered into
the socket (Fig. A-4).
- Press the button seen in Fig. A-5: the led seen in Fig.
A-6 will light up to indicate the USB port is in use.
could seriously damage both devices!
In the event of an emergency, it is possible to place the
The LED lamp is magnetically attached to the starter
(Fig. A-9). You can remove the lamp to use it, simply
grasp it with your hand and pull it towards you. The lamp
has a rechargeable battery: the lamp is automatically
recharged when placed in its housing on the starter with
the switch turned to the OFF position/
RECHARGING
Important! To protect the battery and lengthen its
working life, charge it for 12 hours before using it for
any case, at least every 3 months.
The unit can be recharged using a 230V AC power supply
(using the power supply adapter supplied) or using a 12V
DC power supply. We recommend keeping the battery
fully charged at all times. A low charge level could shorten
the life of the battery. Bear in mind that the time needed
to recharge the battery depends on the number of times it
has been used as a starter. To check whether the battery
needs recharging, press the switch seen in
The three LED'ps seen in Fig. A-2 indicate the charge
status of the battery, with the following meanings:
-
-
-
The red "Charging" LED (Fig. A-11) will light up when unit
is being charged.
The green "Remove Charger" LED (Fig. A-12) will light
up when the unit is being charged to indicate that the
control device that protects the adaptor or battery has
been triggered. It is recommended to disconnect the
adaptor jack from the recharger socket.
Recharging using a 230V AC power supply
1-
To start with, insert the power supply adaptor plug
(Fig. B-1) into a 230V AC socket.
Then insert the relative output plug (Fig. B-2) into
the charger socket (Fig. A-8).
2- The "Charging" LED comes on and the starter is in
device to prevent overcharging the battery and
adaptor. Leave the system to recharge for as long as
necessary.
LED's seen in Fig. A-2 indicate the charge status of
the battery, with the meanings indicated above.
Recharging onboard the vehicle using 12V DC power
1-
Insert the cigar-lighter plug of the supplied cable
(Fig. B-3) into the socket onboard the car or boat.
2- Insert the jack (Fig. B-4) of the supplied cable into
the recharger socket on the starter (Fig. A-8).
the starter as high as possible whilst travelling and may
not allow complete recharging.
Fig. A-7.
Pb

DISPOSING OF THE BATTERY

When the starter battery is completely run down it should
taken be to a re-cycling depot. In some countries this is
mandatory. Contact the local special refuse authority for
information on recycling.
.
This could cause an explosion. Before disposing of the
battery, apply insulating tape to the bare terminals to
prevent shorting. Do not expose the battery to intense
4
: the battery is fully charged.
adapter only!
vehicle is running.
this function is used to keep the charge level of
Do not burn the battery to dispose of it.