Flex SMS 190 18.0-EC Manual De Instrucciones página 31

SMS 190 18.0-EC
– Install the outer flange.
– Press and hold the spindle-lock button,
and use the wrench to turn the blade bolt
counter-clockwise until the lock engages.
Securely tighten the blade bolt.
– Rotate the blade-bolt guard into position,
and use the wrench to securely tighten the
screw by turning it clockwise.
Adjustments
■ ■ Avoid unintentional starting of the machine, Avoid unintentional starting of the machine,
during adjustments on the saw, always during adjustments on the saw, always
remove the battery pack from the saw. remove the battery pack from the saw.
NOTE
The mitre saw was completely adjusted at
the factory. However, during shipment, slight
misalignment may have occurred. Check the
following settings and make adjustments, if
necessary, prior to using the mitre saw.
Aligning the Scale for Mitre
Angles (see figure I1-I2)
– Position the saw head to the closest position
in relation to the fence. And use the arm-lock
pin to secure the saw head in place.
– Set the mitre table at 0°, and set bevel angle
of saw head at 0°.
Checking: (see figure I1)
– Position 90° corner of a combination square
between the fixed fence (14) and the saw
blade on the mitre table (16).
The leg of the square must be flush with the
saw blade over the complete length.
Adjusting (if necessary): (see figure I2)
– Loosen all three screws (I-1) with the
supplied double-ended allen wrench and
turn the mitre table together with the mitre
scale (17) until the leg of the square is flush
with the saw blade over the complete length.
– Retighten the screws again.
When the mitre-angle indicator (19) is not in
line with the 0° mark of the mitre scale after
adjusting, loosen the screw (I-2) with a T25
Torx wrench (not included) and align the
angle indicator alongside the 0° mark.
Setting the Standard Bevel Angle
0° (Vertical) (see figure J1-J2)
– Position the saw head to the closest position
in relation to the fence. And use the arm-lock
pin to secure the saw head in place.
– Set the mitre table at 0°, and set bevel angle
of saw head at 0°.
Checking: (see figure J1)
– Position 90°corner of a combination square
between the mitre table and the saw blade,
ensure it be placed close to fixed fence.
– The leg of the square must be flush with the
saw blade over the complete length.
Adjusting (if necessary): (see figure J2)
– Loosen the bevel-lock knob (34).
– Adjust the set-screw (J-1) in or out by using
the supplied double-ended allen wrench,
until the leg of the square is flush with the
saw blade.
– Once the angle is set, retighten the bevel-
lock knob.
In case of the bevel-angle indicator (10) is not
in line with the 0° mark of the bevel scale (9)
after the adjustment, loosen the screw (J-2) by
using a T25 Torx wrench (not included) and
align the angle indicator with the 0° mark.
Setting the Standard Bevel Angle
45° (Vertical) (see figure K1 and K2)
NOTE
This mitre saw can be tilted to left or right
side. In general, the checking and adjusting
method are the same. Right bevel need to
rotate the bevel-stop lever (11), that is the
only difference between them.
Here raise the right side as an example:
– Position the saw head to the closest position
in relation to the fence. And use the arm-lock
pin to secure the saw head in place.
– Set the mitre table at 0o.
– Move the right sliding fence (13) all the way
out along the horizontal direction.
– Rotate the 45° stop block (32) completely to
the rear of the saw.
– Loosen the bevel-lock knob (34) and rotate
the bevel-stop lever (11) to the other side to
pull it out.
– (For the left bevel this step should be skipped)
– Tilt the tool arm by main handle rightward to
the stop (45°).
Checking (see figure K1):
– Place 45° corner of combination square
between the saw blade and mitre table. The
leg of the square must be flush with the saw
blade over the complete length.
31