Prior To Operation - DeWalt D36000 Traducido De Las Instrucciones Originales

EnGLIsh
INSTRUCTIONS FOR USE
Ensure the machine is placed to satisfy your ergonomic conditions in terms of table height
and stability. The machine site shall be chosen so that the operator has a good overview and
enough free surrounding space around the machine that allows handling of the workpiece
without any restrictions.
To reduce effects of vibration make sure the environment temperature is not too cold, machine
and accessory is well maintained and the workpiece size is suitable for this machine.

WARNING:
• Always observe the safety instructions and applicable regulations.
• Check that the machine has been set up securely.
• Check that the workpiece is properly supported.
• Make sure the cutting disc is not contacting the workpiece before the machine is
switched on.
• Allow the motor to reach full speed before cutting.
• Apply only a gentle pressure to the machine. Do not force the cutting action.
• Keep your hands out of the path of the cutting disc. Do not place your hands within
the marked area on the cutting cart assembly.

Prior to Operation

• Place the tile saw on a horizontal, stable, non‑slip surface.
• Install the appropriate cutting disc.
• Make sure all locking knobs and clamp handles are tight.
• Fill the water basin with the sufficient amount of water for the water pump to be
fully submerged.
• Use only clean water. No other liquid should be used.
MAXIMUM TILE SIZES
Material size (up to)
type
Tile 60 cm x 60 cm x 1.0 cm
Tile 90 cm x 90 cm x 1.0 cm
Tile 94 cm x 20 cm x 1.0 cm
Tile 94 cm x 20 cm x 1.0 cm
Paver 30.5 cm x 30.5 cm x 5.0 cm
Brick 21.5 cm x 10.2 cm x 6.5 cm
Switching On and Off (Fig. R)
• To switch the machine on, set the on/off switch
• To switch the machine off, set the on/off switch
Wired into the mains cable is the portable residual current device (PRCD) containing the
no‑volt release switch and the motor overload protector with manual reset. In case of a power
shut‑off, proceed as follows:
• Make sure the on/off switch is in the off position.
• Press the reset button on the PRCD.
Locking the switch
• In order to avoid unauthorised use of the machine, lock the switch using a padlock.
Cutting Cart Stop Knob (Fig. A, S)
The cutting cart stop knob allows the user to bring the cutting cart assembly
18
the same point each time. To set the position, LIFT UP anD ROTaTE the cutting cart stop
knob and slide the cutting cart back until it stops. It can be set to three different positions
based on the users preference.
• a: Unlock Position: Remove & install cutting cart
• B: Position 1: 90 cm cut capacity. Cutting cart extends past the frame.
• C: Position 2: 45 cm cut capacity. Cutting cart stops at the edge of the frame.
Basic saw cuts
General Handling
• Try a few simple projects using scrap material until you develop a "feel" for the machine.
• Always make dry runs (without power) before finish cuts so that you can check the path of
the cutting disc.
22
Max. Cut Cutting Cart stop
weight knob Position
9 kg Rip cut or Crosscut
20 kg Rip or cross cut
4.5 kg Rip cut
4.5 kg Crosscut
11.7 kg Rip cut or Crosscut
3.1 kg Rip cut or Crosscut
1 to position I.
1 to position 0.
Vertical Straight Cross Cut (Fig. T, X)
1. Set the bevel angle to 0°.
2. Lower the arm to bring the cutting disc into a suitable position.
3. Place the workpiece flat on the table and against the fence, with the finished side up. Align
the marking on the workpiece with the marking in the kerf indicator.
4. Keep both hands away from the path of the cutting disc.
5. Switch the machine on and allow the cutting disc to reach full speed. Wait until the cutting
disc is completely covered with water.
6. Slowly feed the workpiece into the cutting disc, keeping it firmly pressed against the fence.
Do not force. The cutting disc speed should be kept constant.
nOTE: The cutting disc cover can be rotated up to help align the line on the tile with the
cutting disc. Loosen the bolt
cutting disc cover.
7. After completing the cut, switch the machine off, allow the cutting disc to stop and
remove the workpiece.
Bevel Cross‑Cut (Fig. K, U)
Bevel angles can be set at 22.5° and 45°.
1. Loosen the bevel adustment knob
2. Tighten the bevel adustment knob firmly.
3. Proceed as for a vertical straight cross‑cut.
Diagonal Cut (Fig. Y)
The edge guide 19
1. Place the edge guide with the mounting bracket over the fence.
2. Flip the edge guide into position for the required application:
- Flip the edge guide to the right for cutting small pieces from large tiles.
- Flip the edge guide to the left for any other application.
3. Set the edge guide to the required distance.
4. Tighten the knob
5. Proceed as for a vertical straight cross‑cut.
2
Plunge Cut (Fig. W)
1
A plunge cut is used to remove the centre of a tile, e.g. for electrical outlets, drains, etc.
1
1. Mark the area to be cut on both sides of the tile.
2
2. Fit the appopriate size of cutting disc.
2
3. Adjust the cutting depth to allow the cutting disc to saw only halfway through
the workpiece.
2
4. Place the workpiece flat on the table and against the fence, with the finished side up. Align
the marking on the workpiece with the marking in the kerf indicator.
5. Switch the machine on and allow the cutting disc to reach full speed. Wait until the cutting
disc is completely covered with water.
6. Move the table until the marking on the workpiece is underneath the cutting disc.
7. Lower the arm to feed the cutting disc into the workpiece. Do not overcut the mark. As
soon as the marking has been cut, lock the arm into its highest position.
8. Repeat as for the other markings.
9. Turn the workpiece upside down. Proceed as described above for the second cuts to meet
the first.
10. After completing the cut, switch the machine off, allow the cutting disc to stop and
remove the workpiece.
Grooving (Fig. T)
A groove is made into a tile e.g. to accommodate hidden wiring.
back to
11
1. Adjust the cutting depth as required.
2. Place the workpiece flat on the table and against the fence, with the down side up. Align
the marking on the workpiece with the marking in the kerf indicator.
3. Proceed as for a vertical straight cross‑cut.
4. Repeat the procedure to make a wider groove.
Transporting (Fig. N, Y)
The detachable parts can be stored in the water basin for easy transportation.
1. Drain the water basin. See Maintenance.
2. Remove the edge guide and the extension table.
3. Lock the cutting cart in position.
4. Remove the water collectors.
5. Lift the machine out of the water basin as shown.
6. Place the collectors into the water basin in the orientation as shown.
7. Turn the water basin upside down.
8. The edge guide and the extension table can be placed in the water basin before nested.
9. Lift and hold the machine at the carrying points

WARNING: When carrying the machine, always seek assistance. The machine is
too heavy for one person to handle. Always lock the cutting cart before moving or
transporting saw.
59 with the wrench 25 and shown in Fig X and rotate the
45 and set the bevel as desired.
allows cutting of angles at 45°.
to secure the guide in place.
37
61 as shown in Fig. N.