Installation And Start-Up; Fitting The Attachment To The Basic Appliance; Installing Guard Plate (04); Fitting/Removing The Blade (05) - AL-KO solo MT 42.2 Manual De Instrucciones

GB
■
Because of danger of cutting injuries, do not
touch the line cutter with unprotected hands.
■
After pulling out a new line, always bring the
appliance into its normal working position be-
fore switching it on.
■
Do not use a metallic cutting line.
■
Always keep the guard plate, spool head and
motor clear of mowing residues.
■
People who are not familiar with the appli-
ance should practice handling it while the
motor is turned off.
■
When working on a slope:
■
Never work on a smooth and slippery
slope.
■
Always mow across the slope, never
down or up.
■
Always stand below the cutting device.
■
After contact with a foreign object:
■
Switch off the motor.
■
Check the machine for damage.
■
Attach the blade so that it does not loosen
and fall during operation.

6 INSTALLATION AND START-UP

6.1 Fitting the attachment to the basic
appliance
See "Multitool MT 42.2 – basic appliance" operat-
ing instructions.
6.2

Installing guard plate (04)

1. Push guard plate (04/1) onto cutter head
(04/2).
2. Guide screws (04/3) through the guard plate
and screw into holes (04/4).
6.3 Fitting/removing the blade (05)
WARNING! Risk of injury due to detach-
ing appliance parts. Appliance parts detaching
during operation can lead to serious injury.
■
Attach the cutting tools so that they cannot
come loose during operation.
Fitting the blade
1. If fitted: Remove the spool head see chapter
6.4 "Removing/fitting the spool head (06)",
page 20,.
2. Push washer (05/3) and blade (05/1) onto the
drive shaft of cutter head (05/2). The inscrip-
tion on the blade must be facing outwards,
i.e. away from the cutter head.
20
3. Push on cover (05/4).
4. Screw locknut (05/5) onto the drive shaft and
tighten by hand in clockwise direction.
5. Firmly tighten locknut (05/5) with the combi-
nation spanner. Use the retaining pin for
bracing.
Removing the blade
1. Loosen locknut (05/5) in anti-clockwise direc-
tion using the combination spanner. Use the
retaining pin for bracing.
2. Remove locknut (05/5), cover (05/4), blade
(05/1) and washer (05/3).
6.4 Removing/fitting the spool head (06)
WARNING! Risk of injury due to detach-
ing appliance parts. Appliance parts detaching
during operation can lead to serious injury.
■
Attach the cutting tools so that they cannot
come loose during operation.
Fitting the spool head
1. If fitted: Remove the blade see chapter 6.3
"Fitting/removing the blade (05)", page 20,.
2. Push washer (06/3) onto the drive shaft of
cutter head (06/2).
3. Push on spool head (06/1) and screw tight in
clockwise direction. Use the retaining pin for
bracing.
Removing the spool head
1. Loosen spool head (06/1) in anti-clockwise
direction. Use the retaining pin for bracing.
2. Remove spool head (06/1) and washer
(06/3).

7 OPERATION

WARNING! Danger if assembly is not
carried out completely! Use of an incompletely
assembled appliance can result in serious injury.
■
Operate the appliance only when it is fully as-
sembled!
■
Do not insert the battery into the appliance
until it is fully assembled!
7.1

Switching the appliance on and off

See "Multitool MT 42.2 – basic appliance" operat-
ing instructions.
7.2 Prolonging the cutting line during
operation (07)
The cutting line become shorter and frays during
operation.
Installation and start-up
BCA 4235.2