Descargar Imprimir esta página

Checking The Charge Status Of The Rechargeable Battery; Working Behaviour And Working Tech- Nique (10 - 12); Maintenance And Care; Changing The Spool (13) - AL-KO GT 1825 Manual De Instrucciones

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 55
Working behaviour and working technique (10 – 12)
2. Tilt cutter head (09/2) to the desired angle
and allow to engage (09/b).
3. Release the locking button.
7.7
Checking the charge status of the
rechargeable battery
Charge status indicator (01/4) is located on the
top of the basic appliance.
It has three segments. The segments light up or
flash, depending on the battery charge status.
Segment
3 segments lit:
2 segments lit:
1 segment lit:
1 segment flashing:
8 WORKING BEHAVIOUR AND
WORKING TECHNIQUE (10 – 12)
Switch on the appliance before approaching
the grass to be cut and then lower slowly to
avoid overloading.
Tilt the appliance slightly forwards (approx.
30°) to mow with the tip of the cutting line.
Walk forwards slowly (10).
When mowing, swivel the appliance evenly to
the right and left (11).
Long grass must be mown in several passes.
Always proceed from top to bottom (11).
The appliance cuts best at very high speed.
Therefore, do not overload the appliance by
cutting long grass.
If the appliance is overloaded in long grass,
the line will be blocked. Immediately lift the
appliance so it releases. Otherwise, the mo-
tor could be permanently damaged.
Do not move the appliance directly against
hard obstacles (e.g. walls), but mow side-
ways. This protects the cutting line (12).
Keep the appliance away from delicate
plants. Fold the plant protection bar into the
horizontal position.
Allow the appliance to rest on the jockey
wheel when trimming lawn edges. This will
prevent excessive wear of the cutting line
when trimming lawn edges.
443172_a
Battery charge level
Rechargeable battery
fully charged.
Rechargeable battery
2/3 charged.
Rechargeable battery
1/3 charged.
Rechargeable battery
almost flat. The appli-
ance will switch off
shortly.

9 MAINTENANCE AND CARE

WARNING! Danger of cuts and lacera-
tions. Danger of cuts and lacerations when
reaching into sharp-edged, moving appliance
parts and into cutting tools.
Before maintenance, care and cleaning work,
always switch off the appliance. Remove the
rechargeable battery.
Always wear protective gloves during mainte-
nance, care and cleaning work.
NOTE Repair work is only allowed to be car-
ried out by expert workshops or our service cen-
tres.
Do not get the appliance wet or expose it to
moisture. Do not spray with water.
After each use, clean the housing and cutting
blades with a brush or cloth. Do not use wa-
ter and/or aggressive cleaning agents or sol-
vents - risk of corrosion and damage to the
plastic parts.
After every use, remove the rechargeable bat-
tery and inspect the appliance for damage.
Do not use the appliance if the blade of the
line cutter is missing or damaged.
Always keep the guard plate, spool head and
motor clear of mowing residues.
Inspect all bolts for tightness.
Inspect the electrical contacts of the appli-
ance for corrosion, clean with a fine wire
brush if necessary and then spray with a con-
tact spray.
9.1

Changing the spool (13)

Replacement spool: set of 2 (Article No.: 113349)
Precondition: The appliance must be switched off
and the rechargeable battery removed from the
appliance.
Inserting and removing the spool
1. Press (13/a) the two unlocking buttons (13/1)
at the same time and remove cover (13/2).
2. Remove empty spool (13/3).
3. Insert (13/b) a new spool (13/4). Ensure that
spring (13/5) is installed again.
4. Thread the cutting line outwards through
opening (13/6) of the spool head.
5. Fit cover (13/2) and press on until it engages.
6. Install the rechargeable battery in the appli-
ance.
27

Publicidad

loading