Publicidad
Idiomas disponibles
Idiomas disponibles
3.1
Starting and operating of the machine
Check that the electrical switch is switched off (in po-
sition 0). Check that suitable filter are installed in the
machine.Then connect the suction hose into the suc-
tion inlet at the machine by pushing the hose forward
until it fits firmly in place at the inlet. Then connect
the tubes with the hose handle, twist the tubes in
order to ensure that they are properly fitted. Attach
suitable nozzle to the tube. Choose nozzle depend-
ing on what type of material that is to be picked-up.
If used for dust extraction in connection
with dust producing tool then connect end of suction
hose with appropriate adapter. Connect the plug into
a proper electrical outlet. Put the electrical switch
into position I in order to start the motor.
Press I: Activate the machine.
Press 0: Stop the machine.
Hose Ø32, turn clockwise
Turn l: Activate the machine.
Turn
: for AUTO on/off
Turn 0: Stop the machine.
Hose Ø21, turn counterclockwise
Turn l: Activate the machine.
Turn
: for AUTO on/off
Turn 0: Stop the machine.
The hose diameter and the setting for suction hose
diameter must be the same.
ø21
ø32
3.2
Auto-On/Off socket outlet for power tools
CAUTION
Appliance socket
* )
The appliance socket is designed for electri-
cal auxiliary equipment; see technical data for
reference.
•
Prior to plugging in an appliance, always
switch off the machine and the appliance
that is to be connected.
•
Read the operating instructions to the ap-
pliance to be connected and observe the
safety notes contained in these.
An appliance socket with earthing contact is inte-
grated in the machine. An external power tool can
be connected there. The socket features permanent
power on
, when the electrical switch is in position
*)
, i.e. the machine can be used as an extension
cord.
6
OEL=Occupational Exposure Limit,
1)
In position
and off by the power tool connected. Dirt is picked
up from the source of dust immediately. To comply
with regulations, only approved dust producing tools
should be connected.
The maximum power consumption of the connected
electrical appliance is stated in section "Specifica-
tions".
Before turning the switch to position
that the tool connected to the appliance socket is
switched off.
3.3
Push&Clean
The machine is equipped with a semi automatic filter
cleaning system, Push&Clean. The filter cleaning
system must be actuated latest when the suction
performance is no longer sufficient. Regular use of
the filter cleaning feature maintains suction perfor-
mance and increases the lifetime of the filter. For
instruction see quick reference guide.
3.4
Flow rate warning
Check that the filter is present and properly
fitted.
The machine is equipped with a system to
monitor air velocity. Before picking up dust
with occupational exposure limit values, check
the volume flow monitor.
When the motor is running, hold the suction
hose shut to reduce the volume flow. Acoustic
warning sound after some seconds.
Set the diameter setting to the actual hose size.
When the accustic sound starts, air velocity is
below 20 m/s.
•
check if container or filter bag is full.
ø21
•
check if air flow is reduced in suction
hose, tube/nozzle.
ø32
•
Check filter.
*)
3.5
Antistatic connection
The machine is equipped with an antistatic
system to discharge any static electricity that
may develop during dust pick-up.
The antistatic system creates an earth ground con-
nection to the inlet fitting of the container. For proper
function the use of an electrical conductive or anti-
static suction hose is recommended.
3.6
Wet pick-up
The machine is equipped with a float system
that shuts off the airflow through the machine
when the maximum liquid level is reached.
You will hear a noticeable change of the sound
from the motor and notice that the suction
Optional accessories / Option depending on model
*)
the machine can be switched on
ensure
CAUTION
*)
CAUTION
CAUTION
Original instruction
Publicidad
