Publicidad
Idiomas disponibles
Idiomas disponibles
30 | English
Metal cover for cutting
Fit the metal cover for cutting (18) on the protective guard
for grinding (14) (see figure A): Swivel the tool retainer back
(➊). Attach the cover (18) to the protective guard for
grinding (14) (➋). Press the tool retainer firmly into place
on the protective guard (14) (➌).
To remove the cover (see figure B), press the button on the
tool retainer (➊) and swivel it back (➋). Remove the
cover (18) from the protective guard (14) (➌).
Plastic cover for cutting
Attach the plastic cover for cutting (18) to the protective
guard for grinding (14) (see figure C). The cover (18) aud-
ibly and visually engages on the protective guard (14).
To remove the cover (see figure D), unlock the cover (18) on
the left- or right-hand side of the protective guard (14) (➊)
and remove the cover (➋).
Extraction guard for cutting with a guide block
The extraction guard for cutting with a guide block (30) is fit-
ted in the same way as the protective guard for grinding
(14).
Hand guard
Always fit the hand guard (23) when working with the
u
rubber sanding pad (24) or with the cup brush/conical
brush/diamond annular cutter.
Attach the hand guard (23) to the side handle (13).
Standard auxiliary handle/low-vibration auxiliary handle
Screw the auxiliary handle (13)/(12) on the right or left of
the machine head depending on the working method.
Do not operate your power tool without the auxiliary
u
handle (13)/(12).
Do not continue to use the power tool if the auxiliary
u
handle (13)/(12) is damaged. Do not make any altera-
tions to the auxiliary handle (13)/(12).
fortably.
Fitting and removing abrasive tools
Follow the special assembly instructions for
X-LOCK application tools.
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Do not touch grinding and cutting discs until they have
u
cooled down. The discs can become very hot while work-
ing.
Only use original X-LOCK application tools that carry the
u
X-LOCK logo. A maintained clamping gauge of max.
1.6 mm can only be guaranteed with original X-LOCK ap-
plication tools. A higher clamping gauge can lead to insec-
1 609 92A 766 | (17.02.2022)
The low-vibration auxiliary
handle (12) reduces vibra-
tion, enabling the tool to be
used safely and more com-
ure clamping, potentially causing the clamp tool to come
loose.
X-LOCK application tools do not need additional clamping
u
flanges or support flanges.
Make sure that the application tool and the holder are not
u
deformed and are free from dirt and particles.
Pay attention to the dimensions of the abrasive tools.
Make sure that both X-LOCK catches are open (see figure
below) before fitting the X-LOCK application tool.
If necessary, clean the area between the two X-LOCK
catches.
Fitting the abrasive tool
➊ Place the grinding/cutting/flap disc in a central position
on the X-LOCK holder, parallel to the bearing surface
and with the right side facing up.
➋ Push the disc into the holder.
➌ The disc audibly clicks into place. Do not actuate the
lever (3) when doing so.
(3)
After fitting, check that the edge of the abrasive tool
u
(➍) is fitted correctly, i.e. is no higher than the refer-
ence surface (➎). If the edge is higher than the refer-
ence surface, either the holder must be cleaned or the
abrasive tool must not be used.
Before removing the grinding/cutting/flap disc: Make
sure that the power tool has come to a complete stop.
Removing the abrasive tool
➊ Open the lever (3).
➋ The grinding/cutting/flap disc will be released.
➌ The grinding/cutting/flap disc can be removed.
Bosch Power Tools
Publicidad
