Optional Accessory - Makita DTR181 Manual De Instrucciones

NOTICE:
Be sure to mount the wire reel in the
orientation shown in the figure. If it is mounted the
other way around, the wire will be released and may
be twisted.
4. Unhook the wire tip from the hook of reel.
► Fig.13: 1. Hook
5. Make the tip of the wire straight, and pass the wire
through the guide.
► Fig.14: 1. Guide
NOTE: If the tip of the wire is bent when it is passed
through the guide, the wire may become jammed in
the tool.
NOTE: If you force the wire when trying to pass it
through the guide, the wire may become jammed.
6.
Pull the wire out approximately 10 mm from the tip
of the arm.
► Fig.15: 1. Arm 2. Approximately 10 mm
NOTICE:
If the length of the pulled-out wire is
insufficient, the wire may be broken off when tied,
or tying strength may be compromised due to
insufficient wraps.
7. Rewind the wire to eliminate its slack.
► Fig.16
8.
Release the lock lever. The release lever returns,
and the wire is held by the left and right gears.
► Fig.17: 1. Lock lever 2. Release lever
► Fig.18: 1. Gear 2. Path of the wire 3. Wire
NOTICE:
When the lock lever is released and
when the left and right gears mesh with each
other, the grooves in the gears form a space. This
space becomes the path for the wire. Make sure
that the wire is passed through this path.
9.
Close the reel cover.
► Fig.19: 1. Reel cover
Replacing wire guide B

Optional accessory

The wire guide B (in silver color) in the arm can be
replaced with an optional wire guide B (EG) (in black
color) according to the type of tying wire to use.
Find the right combination in the following table. Then
replace the standard equipped wire guide B with an
optional wire guide B (EG) if necessary.
Standard
equipped wire
guide B complete
(silver)
Annealing iron tie wire
Poly coated tie wire
Galvanized tie wire
— : The combination is not valid.
Optional wire
guide B complete
(black)
-
-
1. Loosen bolts A and B using the hex wrench
included in the tool package.
► Fig.20: 1. Hex wrench
► Fig.21: 1. Bolt A 2. Bolt B 3. Contact plate cover
4. Standard equipped wire guide B (silver)
NOTICE:
Do not forcibly remove any bolts that
cannot be removed using the hex wrench.
2. Pull the contact plate cover up in the direction of
the arrow and remove it. Bolt B will be removed at the
same time.
► Fig.22: 1. Contact plate cover 2. Bolt B
3. Remove bolt A, and remove the standard
equipped wire guide B (silver).
► Fig.23: 1. Bolt A 2. Standard equipped wire guide
B (silver)
4. Replace the standard equipped wire guide B (in
silver color) with an optional wire guide B (EG) (in black
color).
► Fig.24: 1. Optional wire guide B (EG) (in black
color).
5.
Align the pipe of the tool with the groove inside the
optional wire guide B (EG) (black), and assemble them.
► Fig.25: 1. Pipe 2. Groove 3. Optional wire guide B
(EG) (black).
6. Fix the optional wire guide B (EG) (black) by tem-
porarily tightening bolt A.
► Fig.26: 1. Bolt A 2. Optional wire guide B (EG)
(black).
7. Install the contact plate cover in the direction of
the arrow.
► Fig.27: 1. Contact plate cover
8. Fix the optional wire guide B (EG) (black) and con-
tact plate cover securely by tightening bolt A and bolt B.
► Fig.28: 1. Optional wire guide B (EG) (black).
2. Contact plate cover 3. Bolt A 4. Bolt B
9. After assembling, confirm that the contact plate
can move as shown in the figure.
► Fig.29: 1. Contact plate
NOTE: If the contact plate is caught, press it as
shown in the figure.
► Fig.30
OPERATION
Checking before work
CAUTION:
If the tool has a safety mecha-
nism-related problem, do not use it. If you continue
to use it, an accident may occur.
Before using the tool, make sure that the safety mecha-
nism operates normally. If the tool operates without the
safety mechanism operating, stop using the tool imme-
diately. Ask your local Makita Service Center for repairs.
18 ENGLISH