Publicidad
Idiomas disponibles
Idiomas disponibles
English
Cutting (Fig. A, D–G)
The blade
7
should extend past the pivoting shoe
the thickness of the workpiece throughout the cut. Select
the blade best suitable for the material to be cut and use the
shortest blade suitable for the thickness of the material.
nOTE: Do not use jigsaw blades with this tool.
nOTE: Before cutting any type of material, be sure it is firmly
anchored or clamped to prevent slipping.
•
Place blade
7
and pivoting shoe
to be cut.
•
Switch on saw motor and allow it to obtain maximum
speed before applying pressure.
•
Always hold saw firmly with both hands while cutting as
shown in Fig. D. Whenever possible, the pivoting shoe
must be held firmly against the material being cut. This
will prevent the saw from jumping or vibrating and will
minimize blade breakage.
Wood Cutting (Fig. E, F)
1. Before cutting any type of wood, be sure the workpiece
is firmly anchored or clamped to prevent slipping.
2. Place blade
7
and pivoting shoe
to be cut.
3. Switch on saw motor before starting the cut.
4. Always hold saw firmly with both hands while cutting.
Whenever possible, the pivoting shoe must be held
firmly against the material being cut. This will prevent
the saw from jumping or vibrating and minimize
blade breakage.
Metal Cutting (Fig. G)
1. Use a finer blade for ferrous metals and a coarse blade for
non‑ferrous materials.
2. In thin gauge sheet metals it is best to clamp wood to
the underside of the sheet. This will ensure a clean cut
without excess vibration or tearing of metal.
3. Avoid forcing cutting blade as this reduces blade life and
causes costly blade breakage.
nOTE: You should spread a thin film of oil or other coolant
along the line ahead of the saw cut for easier operation
and longer blade life. For cutting aluminum, kerosene
is preferred.
Pocket Cutting - Wood Only (Fig. H)
Measure the surface area to be cut and mark clearly with a
pencil, chalk or scriber.
1. Insert blade
7
in blade clamp collar
clamp securely.
2. Tip the saw backward until the back edge of the pivoting
shoe is firmly on the work surface.
3. Switch motor on, permitting blade to attain
maximum speed.
4. Grip handle steadily and begin a slow, deliberate upward
swing with the handle of the saw.
5. The blade will begin to feed into material. Always be sure
blade is completely through material before continuing
with pocket cut.
10
5
and
5
lightly against work
5
firmly against work
6
and tighten blade
nOTE: In areas where blade visibility is limited, use the edge
of the pivoting shoe as a guide.
Project Tips
•
Cut only with sharp blades; they cut cleaner, faster and put
less strain on the motor while cutting.
•
When cutting, always ensure that the pivoting shoe is
resting against the workpiece. This will improve operator
control and minimize vibration.
•
For longer blade life, use bi‑metal blades or carbide
tipped blades. These utilize a carbon steel back welded
to high speed steel teeth making the blade more flexible
and less prone to breaking.
Worklight (Fig. A)
The worklight
is activated when the trigger switch is
10
depressed, and will automatically turn off 20 seconds after
the trigger switch is released. If the trigger switch remains
depressed, the worklight will remain on.
nOTE: The worklight is for lighting the immediate work
surface and is not intended to be used as a flashlight.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Your PORTER‑CABLE power tool has been designed to
operate over a long period of time with a minimum of
maintenance. Continuous satisfactory operation depends
upon proper tool care and regular cleaning.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Accessories
WARNING: Since accessories, other than those
offered by PORTER‑CABLE, have not been tested with
this product, use of such accessories with this product
could be hazardous. To reduce the risk of injury, only
PORTER‑CABLE recommended accessories should be
used with this product.
Recommended accessories for use with your
product are available at extra cost from your local
dealer or authorized service center. If you need
assistance in locating any accessory, please contact
PORTER‑CABLE call 1‑888‑848‑5175 or visit our website:
www.portercable.com.
Publicidad
