Commissioning; Usb Port; Checking Accumulator Status; Maintenance And Service - Narex CR LED 20 Instrucciones De Uso Originales

English
The following must be maintained during battery transpor-
tation:
• Make sure that contacts are protected and isolated to prevent
a short circuit�
• Be careful so that a large number of batteries do not move
around or fall and collapse during transport�
• Damaged and leaking batteries cannot be transported�
Please contact your carrier for additional information�
Warning!!
It is not expected for the user to perform any service repairs on the
charger� There are no spare parts inside the charger, which users
could repair on their own� It is necessary to bring the charger to
your nearest authorised service centre to prevent damage to spare
parts, which are sensitive to static electricity, for example�
Always use the right set of batteries (the set delivered with the
tools or a replacement set recommended by Narex s�r�o�)� Never
use any other sets of accumulator batteries because they could
damage your tools and cause a hazardous situation�

Commissioning

Inserting and removing a battery
Insert the battery (B1) into the shaft on the bottom side of the
machine handle all the way� Pull on the battery to make sure it is
fitted properly�
To remove the accumulator (B1) from the machine, push on the
accumulator clamp (B2) and pull the accumulator out�
Turning On and Off
Pressing the switch (1) turns on the work light at 50 % output�
Pressing the switch (1) again turns up the work light to 100 % out-
put� Pressing the switch (1) one more time turns the work light off�
Tilting the Spotlight
The spotlight (2) can be tilted at a -90° to 90° angle in 30° steps� To
tilt the spotlight to the position of choice, hold the work light by
the accumulator with one hand, place your other hand on the work
light's handle and tilt the spotlight�
Attention!
The flashlight uses a highly luminous LED as its light source� Make
sure you or other persons (or animals) in your vicinity do not look
directly into the light source� There is a risk of glare, which may re-
sult in subsequent injury of the blinded person (or animal)�

USB port

The USB port (3) is only used to provide power (or charging) to an
external device�
To connect an external device to the USB port, remove the rubber
cap from the USB port and plug in the USB cable�
After you unplug the USB cable, cover the USB port with the rubber
cap again to prevent dirt from entering the interior of the port�
The USB port can only be used to supply power when the accu-
mulator is in the work light� External devices can be powered even
when the work light is turned off�

Checking Accumulator Status

The machine is fitted with an accumulator status control panel (B3)�
Press the control button (B4) on the accumulator status panel (B3)�
An accumulator status indicator (B5) will light up based on the
state of charge (capacity) of the accumulator�
Overview of accumulator's state of charge (capacity) indication:
Number of fully lit LEDs
3
2
1
16
Accumulator's state of charge
100 %
less than 60 %
less than 30 %

Maintenance and service

Instructions for flashlight cleaning
Clean the external plastic parts by a wet rag and mild detergent�
Though these parts are made of the materials resistant to solvents,
NEVER use any solvent�
Instructions for cleaning the charger
Attention! Risk of electric shock. Prior to start handling
the charger, disconnect the line plug from the socket!
Impurities and dust can be removed from external charg-
er surfaces by a rag or a non-metal brush� Use neither water nor
detergents�
Attention! With respect to protection from el. shock
and preservation of the class of protection, all mainte-
nance and service operations requesting jig saw case
removal must be performed by the authorized service
centre only!
The current list of authorized service centres can be found at our
website www.narex.cz, section "Service centres"�

Storage

Packed appliance may be stored in dry, unheated storage place
with temperature not lower than -5 °C�
Unpacked appliance should be stored only in dry storage place
with temperature not lower than +5 °C with exclusion of all sudden
temperature changes�

Environmental protection

Power tools, accessories and packaging should be sorted for envi-
ronmental-friendly recy�
Only for EU countries:
Do not dispose of power tools into household waste!
According to the European Directive 2002/96/EC on waste electri-
cal and electronic equipment and its incorporation into national
law, power tools that are no longer suitable for must be separately
collected and sent for recovery in an environmental-friendly man-
ner�

Warranty

Our equipment is under warranty for at least 12 months with re-
gard to material or production faults in accordance with national
legislation� In the EU countries, the warranty period for exclusively
private use is 24 months (an invoice or delivery note is required as
proof of purchase)�
Damage resulting from, in particular, normal wear and tear, over-
loading, improper handling, or caused by the user or other dam-
age caused by not following the operating instructions, or any
fault acknowledged at the time of purchase, is not covered by the
warranty�
Complaints will only be acknowledged if the equipment has not
been dismantled before being sent back to the suppliers or to an
authorised NAREX customer support workshop� Store the operat-
ing instructions, safety notes, spare parts list and proof of purchase
in a safe place� In addition, the manufacturer's current warranty
conditions apply�
Note
Due to continuous research and development work, we reserve
the right to make changes to the technical content of this docu-
mentation�