Publicidad
Idiomas disponibles
Idiomas disponibles
Attaching the Water Tank (Fig. C)
1. Install the water tank
ensuring the water tank is securely in place.
Attaching the Cleaning Pad (Fig. A, D)
Replacement cleaning pads, SMP20, are available from
your BLACK+DECKER dealer. Replacement cleaning pads
for Lift+Reach™ head are SMP30
1. Place cleaning pad
7
facing up.
2. Lightly press steam mop or Lift+Reach™ head down
onto the cleaning pad. You are now ready to steam
clean and sanitize your floor.
NOTICE: Do not store with a wet pad as this can
damage your floor. Always place the steam mop with
the handle
4
in the upright position when stationary
and make sure the steam mop is turned off when not
in use.
Removing a Cleaning Pad
WARNING: Always wear suitable shoes when
changing the cleaning pad on your steam mop. Do
not wear slippers or open toed footwear.
1. Return the handle
4
the steam mop OFF'
2. Wait until the steam mop cools down (approximately
5 minutes).
3. Lift the steam mop away from the cleaning pad freeing
it from the velcro fastening.
WARNING: Always place your steam mop with the
handle
4
supported in the upright position when
stationary and make sure the steam mop is turned off
when not in use.
Filling Water Tank (Fig. E)
WARNING: Do not over fill the tank.
nOTE: Do not use chemical cleaners with your steam mop
water tank.
nOTE: Fill the water tank with clean tap water.
nOTE: In areas of hard water, the use of distilled water
is recommended.
nOTE: Ensure the filler cap is firmly secured.
nOTE: Always empty the water tank after use.
1. Make sure the steam mop is turned OFF and unplugged.
2. Remove water tank from the steam mop body.
3. Open the water tank filler cap
4. Fill the water tank
3
5. Replace the water tank filler cap
nOTE: Ensure the water tank filler cap
firmly secured.
WARNING: Your water tank has a 380 ml capacity.
Do not over fill the tank.
OPERATION
CAUTION: Never use the steam mop without first
attaching a cleaning pad.
3
to the steam mop body
on the floor with the "loop" side
to the upright position and turn
13
.
with water.
13
.
13
is
iMPORTAnT: This unit will kill 99.9% of germs when used in
accordance with the instructions in this manual and with the
micro-fiber pad fitted and a continuous run time of 90 seconds.
NOTICE: Do not use on any unsealed hard floor
surfaces. Additionally, on surfaces that have been
treated with wax or some no wax floors, the sheen
may be removed by the heat and steam action. It
is always recommended to test an isolated area of
the surface to be cleaned before proceeding. We
also recommend that you check the use and care
instructions from the floor manufacturer.
NOTICE: Never leave the steam mop in one spot on
any surface for any period of time. Do not store with a
wet pad as this can damage your floor. Always place
the steam mop with the handle tube
position when stationary and make sure the steam
mop is turned OFF and unplugged when not in use.
NOTICE: Always empty the water tank after use.
Switching On and Off (Fig. A)
nOTE: It takes approximately 30 seconds for the steam mop
to heat up.
1. To switch the appliance ON, press the On/Off button
2. Press the steam operation button
the pump and the unit will begin to produce steam.
3. To stop steam generation, press steam operation
button
2
a second time. This will maintain power to
the boiler for quicker start up.
4. To switch the appliance OFF, press the On/Off button
NOTICE: Never leave the steam mop in one spot on
any surface for any period of time. Always place the
steam mop with the handle tube
upright position when stationary and make sure the
steam mop is turned off when not in use.
NOTICE: Always empty the steam mop after use.
nOTE: When first filled or after running dry, it can take up to
45 seconds for steam to be produced.
The Lift+Reach
TM
This Steam Mop incorporates a built in Lift+Reach™ head
which enables you to access tight corners and narrow gaps.
CAUTION: Always wear suitable shoes when
accessing the Lift+Reach head on your steam mop.
Do not wear slippers or open-toed footwear.
To Access the Lift+Reach Head
1. Return the handle to the upright position and turn the
steam mop OFF.
2. Wait until it cools down (approximately five minutes).
Place the front of your shoe onto the steam head
removal tab
and press down gently.
12
3. Lift the Lift+Reach™ head up off the steam head
4. Place the Lift+Reach™ head cleaning pad
with the hook and loop side facing up.
5. Press the Lift+Reach™ head down onto the cleaning
pad
8
. You are now ready to steam clean and sanitize
your floor.
4
in the upright
2
. This will operate
4
supported in the
Head (Fig. F)
8
on the floor
English
1
.
1
.
5
.
5
Publicidad
