Makita HR160D Manual De Instrucciones página 4

ENGLISH
(Original instructions)
1 Set plate
2 Battery cartridge
3 Switch trigger
4 Reversing switch
5 Action mode changing knob
6 Bit shank
SPECIFICATIONS
Model
Capacities
Concrete ............................................................ 16 mm
Steel ................................................................... 13 mm
Wood .................................................................. 20 mm
-1
No load speed (min ) .......................................... 0 – 950
Blows per minute ............................................... 0 – 3,600
Overall length ..................................................... 296 mm
Net weight ............................................................. 2.5 kg
Rated voltage ..................................................... D.C.12 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications and battery cartridge may differ from
country to country.
• Weight, with battery cartridge, according to EPTA-Pro-
cedure 01/2003
Intended use
The tool is intended for hammer drilling and drilling in
brick, concrete and stone as well as for chiselling work.
It is also suitable for drilling without impact in wood,
metal, ceramic and plastic.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
CORDLESS ROTARY HAMMER SAFETY
WARNINGS
1. Wear ear protectors. Exposure to noise can cause
hearing loss.
2. Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
3. Hold power tools by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring. Cutting
accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
4
All manuals and user guides at all-guides.com
Explanation of general view
7 Bit grease
8 Bit
9 Chuck cover
10 Chisel adapter
11 Clamp screw
12 Chisel
4.
HR160D
5.
6.
7.
8.
9.
ENE043-1
10. Keep hands away from moving parts.
11. Do not leave the tool running. Operate the tool
12. Do not point the tool at any one in the area when
13. Do not touch the bit or parts close to the bit
GEA010-1
14. Some material contains chemicals which may be
SAVE THESE INSTRUCTIONS.
WARNING:
GEB046-2
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this instruc-
tion manual may cause serious personal injury.
13 Depth gauge
14 Dust cup
15 Blow-out bulb
16 Drill chuck assembly
Wear a hard hat (safety helmet), safety glasses
and/or face shield. Ordinary eye or sun glasses
are NOT safety glasses. It is also highly recom-
mended that you wear a dust mask and thickly
padded gloves.
Be sure the bit is secured in place before opera-
tion.
Under normal operation, the tool is designed to
produce vibration. The screws can come loose
easily, causing a breakdown or accident. Check
tightness of screws carefully before operation.
In cold weather or when the tool has not been
used for a long time, let the tool warm up for a
while by operating it under no load. This will
loosen up the lubrication. Without proper warm-
up, hammering operation is difficult.
Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
Hold the tool firmly with both hands.
only when hand-held.
operating. The bit could fly out and injure some-
one seriously.
immediately after operation; they may be
extremely hot and could burn your skin.
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.