Descargar Imprimir esta página

Bilanciai STB80 Manual De Uso Y Mantenimiento página 33

Publicidad

1 Access the SETUP mode by keeping the
GB
Feed key depressed before powering the
printer and keeping it depressed for a few
seconds after the printer has been powered.
2 The printer should print the list of all
the parameters:
1 Entrare nel
SETUP
I
Feed prima dell'accensione della stampante
e mantenendo la pressione per qualche
secondo dopo l'accensione stessa .
2 La stampante stamperà la lista di tutti i
parametri:
SETUP
All manuals and user guides at all-guides.com
tenendo premuto il tasto
Notes
default values.
Note :
Note :
USB interface; it is used to identify univocally the USB
printer by a numerical address code, if the PC is
connected to two printers of the same model.
Note :
by the user but depends on the "Speed/Quality" parameter in
this way: when the normal or high speed parameter is selected,
the current consumption will be set as high current;
when the low speed parameter is selected, the current
consumption will be set as low current.
Note :
enabled only if the notch alignment parameter is enabled.
The parameter "Notch distance" is used to set the exact
distance of the notch by entering the desired value in
millimetres and in tenth of millimetre.
Note :
makes a partial cut because the total cut command will
be ignored; otherwise when the total cut command (ESC i)
is enabled, it will be executed.
Note :
switched on automatically, if a power failure occurs, without
pressing On-Off key.
-"
(ON or OFF) before the power failure;
-"
after a power failure;
-"
the On-Off key, after a power failure.
RS232 Baud Rate :
(1)
115200, 57600,38400, 19200 ,
9600, 4800, 2400, 1200.
RS232 Data length :
(1)
7, 8 bits/char.
RS232 Parity :
(1)
None , even or odd.
D
RS232 Handshaking :
(1)
XON/XOFF or Hardware .
Busy condition :
(1)
OffLine/RxFull or RxFull .
USB Address Number :
(2)
Autofeed:
CR disabled or CR enabled.
D
Print mode:
Normal or reverse.
D
Chars/inch:
A=11 B=15 cpi, A=15 B=20 cpi .
Speed/Quality :
(3)
Normal , High Quality or High Speed.
Printing Width:
76mm [80 PaperW] , 80mm [82.5
PaperW].
Notch alignment:
Disabled , Enabled.
Notch Threshold :
(4)
0.5, 1.0, 1.5, 2.0, 2.5, 3.0, 3.5 ,
4.0, 4.5.
Notch distance (mm):
(4)
00.0
Total cut (ESC i) :
(5)
Disabled , Enabled.
PaperEnd Buffer Clear:
PowerFail WakeUp mode :
Always OFF, Always ON.
Print Density:
-50%, -37%, -25%, -12%, 0 ,+12%,
+25%,+37%, +50%.
: The parameters marked with a symbol are the
(1)
Parameters valid only for serial printers.
(2)
This parameter is displayed if the printer has an
(3)
The "Current consumption" parameter cannot be setted
(4)
The parameter "Notch distance" is displayed and
(5)
When this parameter is disabled the printer always
(6)
When this parameter is used, the printer can be
LAST PWR State
" : Returns the printer in the previous status
Always ON
" : The printer always switches on automatically,
Always OFF
" : The printer can only be switched on by pressing

STB80
D
D
D
D
0.
D
D
D
D
D
D
D
Disabled , Enabled.
D
(6)
LAST PWR State ,
D
D
D

Publicidad

loading

Productos relacionados para Bilanciai STB80