Important - MonkeyLink ML-SkyeLight 110 LUX Manual De Instrucciones

Operating manual for headlight
»ML-SkyeLight 110 LUX«
Technical data and information
M ain light source: 2 high-performance-LED (300 Lm)
u
H igh beam function: 4 high-performance-LED (600 Lm)
u
D ayrunning-light function: 35 pcs COB-LED
u
P erformance: 5 W/10 W High beam function
u
Input voltage: 12 V DC
u
Tested and approved in accordance with the
u
German Road Traffic Licensing Regulations (StVZO)

Important:

The 12 V DC version is marked with the
Attaching the lamps:
W hen attaching the lamps, the light of the e-bike system must be switched off.
u
O nly switch the light on when the lamp is fitted to the e-bike.
u
If your e-bike system does not have a light switch, the battery must be removed when attaching the lamps.
u
Adjust the angle of the light in such a manner that you have optimum illumination, starting immediately
u
in front of the front wheel. Please ensure that you do not set the light too high and
thus dazzle traffic travelling in the opposite direction. The headlight is to be installed
in such a manner that the light beam meets the road approx. 10 m in front of the bike.
To adjust the headlight, turn the adjustment screw on the left side.
u
Before every journey, ensure that the headlight is clear when steering (it must not get stuck) and is not covered.
u
The following mounting heights apply for headlights on bicycles:
u
min. height: 400mm, max. height: 1200mm
In order to link the MonkeyLink module to the bike, move it with the integrated part of the holder (connector (2.))
within close proximity of the base (1.) until you feel the magnetic attraction. Lock the accessory section into the
base until you hear a click sound from the mechanical coupling. Ensure that the rocker arm (3.) is fully engaged.
To remove the MonkeyLink module, operate the rocker arm (3.) and pull the module forward out of the coupling.
(1.) Base
(2.) Connector
Use of USB-C plug:
1. Switch on e-bike
u
ATTENTION! The light must be switched on before charging the device,
otherwise an error will occur in the e-bike system.
Use of the anti-theft screw:
T he anti-theft screw is pre-installed on the lamp side. If the lamp should remain
u
permanently on the bike (e.g. as theft protection), loosen the screw for angle
adjustment. Then carefully lift the roller until the screw hole is accessible to the
anti-theft screw. Connect the modules and screw the anti-theft screw into place
with a 1.5 mm hexagon key with approx. 3 rotations. Then place the front light on
the roller again, set the correct angle and tighten the roller screw firmly.
PLEASE NOTE: The utmost care is required during assembly. We recommend having
a specialist retailer take care of assembly.
Transporting the lamps:
P lease remember that the lamp must be protected when transported in a bag. The contacts, in
u
particular, must be protected against mechanical influences.
T he fastenings must be checked for dirt and any adhering metal items before attachment.
u
(3.) Rocker arm
Removable
reflector K
1712
2. Switch on light
u u
symbol DC AC. It should be noted that the use
of the 12 V DC AC version is only permitted for
bicycles with electric assisted pedalling (e-bikes)
if, following a discharge-based shut-down of the
support drive, an uninterrupted power supply to
the lighting system is ensured for at least two
hours, or if the drive motor can be used tempora-
rily as a generator in order to continue to supply
power to the lighting system.
The light is switched on/off using the bike control
unit with pedal assistance.
Angle adjustment
USB Plug
3. Plug in device
Switch high beam function
when the high beam
function is active, the
switch lights up blue
When the device is charging,
the white LEDs in the side slots
flash
Anti Theft Screw
GB