Tabla De Contenido; Before Using; Cautions On Installation; Cautions On Handling - Denon AVR-1802 Instrucciones De Operación

Idiomas disponibles

2 We greatly appreciate your purchase of the AVR-1802.

2 To be sure you take maximum advantage of all the features AVR-1802 has to offer, read these

instructions carefully and use the set properly. Be sure to keep this manual for future reference

should any questions or problems arise.

"SERIAL NO.

PLEASE RECORD UNIT SERIAL NUMBER ATTACHED TO THE REAR OF

THE CABINET FOR FUTURE REFERENCE"

2 INTRODUCTION

Thank you for choosing the DENON A/V Surround receiver. This remarkable component has been engineered to

provide superb surround sound listening with home theater sources such as DVD, as well as providing outstanding

high fidelity reproduction of your favorite music sources.

As this product is provided with an immense array of features, we recommend that before you begin hookup and

operation that you review the contents of this manual before proceeding.

TABLE OF CONTENTS

Before Using .......................................................3

Cautions on Installation .......................................3

Cautions on Handling ..........................................3

Features ..............................................................3

Part Names and Functions ..................................4

Read this First .....................................................5

Setting up the Speaker Systems.........................5

Connections..................................................5 ~ 8

Using the Remote Control Unit...........................9

⁄0

Setting up the system ................................9 ~ 11

2 ACCESSORIES

Check that the following parts are included in addition to the main unit:

q Operating instructions.................................1

w Service station list ....................................1

e Remote control unit (RC-897) .....................1

r R6P/AA batteries .......................................2

1 BEFORE USING

Pay attention to the following before using this unit:

• Moving the set

To prevent short circuits or damaged wires in the

connection cords, always unplug the power cord and

disconnect the connection cords between all other

audio components when moving the set.

• Before turning the power operation switch on

Check once again that all connections are proper and

that there are not problems with the connection cords.

Always set the power operation switch to the

standby position before connecting and disconnecting

connection cords.

⁄1

Remote Control Unit ...................................12, 13

⁄2

Operation ..................................................13 ~ 15

⁄3

Surround ...................................................16 ~ 18

⁄4

DSP Surround Simulation .........................18 ~ 20

⁄

Listening to the Radio...............................20 ~ 23

⁄6

Last Function Memory ......................................23

⁄7

Initialization of the Microprocessor ...................23

⁄8

Additional Information .................................24, 25

⁄9

Troubleshooting ................................................25

¤0

Specifications ....................................................26

List of Preset Codes ...............................................171

t AM loop antenna .......................................1

y FM indoor antenna ....................................1

u FM antenna adaptor .................................1

• Store this instructions in a safe place.

After reading, store this instructions along with the

warranty in a safe place.

• Note that the illustrations in this instructions may

differ from the actual set for explanation purposes.

• V. AUX terminal

V.AUX INPUT

SURROUND

SELECT

OPTICAL

VIDEO

L AUDIO R

MODE

EAT

The AVR-1802's front

SURROUND

PARAMETER

panel is equipped with a

V. AUX terminal. Remove

the cap covering the

terminal when you want

to use it.

2 CAUTIONS ON INSTALLATION

Noise or disturbance of the picture may be generated

if this unit or any other electronic equipment using

microprocessors is used near a tuner or TV.

If this happens, take the following steps:

• Install this unit as far as possible from the tuner or

TV.

• Set the antenna wires from the tuner or TV away from

this unit's power cord and input/output connection

cords.

• Noise or disturbance tends to occur particularly when

using indoor antennas or 300 Ω/ohms feeder wires.

We recommend using outdoor antennas and 75

Ω/ohms coaxial cables.

For heat dispersal, leave at least 10 cm of space

between the top, back and sides of this unit and the

wall or other components.

3 CAUTIONS ON HANDLING

• Switching the input function when input jacks are

not connected

A clicking noise may be produced if the input function

is switched when nothing is connected to the input

jacks. If this happens, either turn down the MASTER

VOLUME control or connect components to the input

jacks.

• Muting of PRE OUT jack, HEADPHONE jack and

SPEAKER terminals

The PRE OUT jack, HEADPHONE jack and

SPEAKER terminals include a muting circuit.

Because of this, the output signals are greatly

4 FEATURES

1. Dolby Pro Logic II decoder

Dolby Pro Logic II is a new format for playing

multichannel

audio

signals

improvements over conventional Dolby Pro Logic.

It can be used to decode not only sources recorded

in Dolby Surround but also regular stereo sources

into five channels (front left/right, center and

surround left/right). In addition, various parameters

can be set according to the type of source and the

contents, so you can adjust the sound field with

greater precision.

2. Dolby Digital decoder

Dolby Digital, a digital discrete system in which the

different channels are completely independent,

recreates "three-dimensional" sound fields (sounds

with a sense of distance, movement and position)

with no crosstalk between channels for greater

reality. In addition, the 5 channels (excluding the 0.1

channel for low frequency effects) have a playback

CH VOL

range extending to 20 kHz, the same as the range

TONE

CONTROL

of CDs, thus resulting in clearer, more richly

expressive sound.

3. DTS (Digital Theater Systems) decoder

DTS provides up to 5.1 channels of wide-range, high

fidelity surround sound, from sources such as laser

disc, DVD and specially-encoded music discs.

10 cm or more

reduced for several seconds after the power

operation switch is turned on or input function,

surround mode or any other set-up is changed.

If the volume is turned up during this time, the output

will be very high after the muting circuit stops

functioning. Always wait until the muting circuit turns

off before adjusting the volume.

• Whenever the power operation switch is in the

OFF or STANDBY state, the apparatus is still

connected on some AC line voltages.

Please be sure to unplug the cord when you leave

home for, say, a vacation.

4. High performance DSP simulates 7 sound fields

Playback is possible in 7 surround modes: 5-channel

that

offers

Stereo, Mono Movie, Rock Arena, Jazz Club, Video

Game, Matrix and Virtual. You can enjoy a variety of

sound effects for different movie scenes and

program sources even with stereo sources not in

Dolby Surround.

5. Personal Memory Plus function

Personal Memory Plus is an advanced version of

Personal Memory. With Personal Memory Plus, the

set automatically memorizes the surround mode,

channel volume, surround parameters, etc., for each

of the separate input sources.

6. Remote control unit with pre-memory function

This unit comes with a remote control unit equipped

with a pre-memory function. The remote control

command codes for DENON remote controllable AV

components as well as for LD players, video decks,

TVs, etc., of other major manufacturers are prestored

in the memory.

7. EXT. IN jack

This unit is equipped with EXT. IN jacks for use with

audio formats of the future.

ENGLISH

10 cm or more

wall