JBL SYNTHESIS SDR-38 Manual página 24

To delete the learned data for a key for a device:
1. Press the Device key for the product you want to set up,
together with the key. Hold down both buttons for
three seconds until the LED stays lit.
2. Press and hold down the key on which you want
to delete the data for three seconds. The LED blinks
twice ** . If any further key press is made, the
remote escapes from erase mode without deleting
the learned data.
3. If any further key press is not made for 30 seconds,
**
the LED blinks twice , the remote escapes from
the erase mode automatically without deleting the
learned data.
4. If you press the Device key together with the
again within 30 seconds after the LED blinks twice, all
the data learned for that Device is deleted and you
leave erase mode. The LED blinks three times ***
in confirmation.
Reading stored code numbers
1. Press the Device key for the product that you want to
set up together with the key. Hold down both keys for
three seconds until the LED blinks.
2. Press the key and count the number of blinks
( * =1, ** =2, *** =3, etc.). There is a time
gap between digits. (Note that '0' is represented by ten
blinks: ********** .)
Locking/unlocking a specific
Device Mode
When you first unpack your remote and insert the batteries,
it is able to control certain JBL Synthesis components
automatically (e.g. BD players, Amplifiers, Tuners and CD
Players). We achieve this by programming specific JBL
Synthesis device codes onto the relevant Device Mode keys,
then locking the Device Modes so you don't reprogram
them inadvertently.
If you want to override these locked default settings – to
control a third-party BD player, for example – you will first
need to unlock BD Mode before setting up the remote
using one of the learning methods described on the
previous page.
key
Here are the factory default settings:
Device Default Default
Mode status codes
Locked 001 (JBL Synthesis code 16)
AMP
BD Locked 001 (JBL Synthesis)
AV Unlocked 108 (Philips TV)
UHD Unlocked Code learning only
GAME Unlocked Code learning only
STB Unlocked 030 (Bush/Goodmans/
Grundig, from SAT database)
Unlocked 128 (Sky+ Digital, from SAT
SAT
database)
PVR Unlocked 018 (Humax PVR, from SAT
database)
CD Locked 001 (JBL Synthesis)
Alternative codes are available for multi-room solutions, or in
the case of code clashes with other manufacturer's products.
For example:
(system code 19): 002
Note that you need to change the system code on the
product you wish to control, as well as the remote.
1. and are the Device keys that may be Locked
AMP, BD CD
or Unlocked.
Lock and Unlock are toggles (they change from Lock to
Unlock to Lock, etc.).
2. Press and hold the Device and keys together for three
seconds.
The power LED stays lit, showing that it is in Lock/Unlock
setup mode.
3. If there is no further key input for 30 seconds, the LED
goes off and the remote leaves Lock/Unlock setup mode.
4. To toggle the status of a device and then verify the status
of a device, press the keys in sequence:
If you have locked the device, the LED blinks three times:
***
.
If unlocked the device, the LED blinks five times:
*****
.
5. If you press a valid Device key within 30 seconds, the
***
LED blinks three times: and the remote leaves
Lock/Unlock setup mode.
Controlling the volume of other
devices
By default, the volume keys and mute key control the
amplifier volume.
You can configure these buttons so they send volume
commands to another device. In the following example,
the volume commands are sent to a linked AV device (your
television, for instance):
1. Press + for three seconds, until the LED lights and
stays on.
2. Press .
UP
again. The LED blinks three times *** .
3. Press
The volume and mute keys will now send the volume
commands to the TV.
To set the volume buttons to control the amplifier once
more, repeat the above steps, except press in step 3.
EN-23
Hidden commands
Command Effect
'
Sends a Power On command
AMP +
,
Sends a Power Off command
AMP +
Sends a Zone command
AMP + OK
>
Cycles through HDMI outputs 1, 2, 1&2.
AMP +
'
Sends a Power On command
CD +
,
Sends a Power Off command
CD +
'
Sends a Power On command
BD +
,
Sends a Power Off command
BD +
>
Sends a Resolution command
BD +
Factory default reset
You can reset your remote to the original factory default
settings.
Press and hold both the (home) and keys for
about five seconds until the power LED blinks five times
*****.
All programming and setup codes that you have entered
into the remote are erased and the remote returns to the
original factory default settings.
Device codes
The tables that are in the final section of this Handbook list
3-figure codes for different manufacturers' devices.
Use these when setting your remote up to control your
devices, as described in Direct code setup: Method 1 (see
previous page).
If more than one code number is listed, try the first
number. If the results are unsatisfactory, continue trying the
numbers for that manufacturer to get the best 'fit' with the
functionality required.
If the manufacturer of your equipment is not listed, you can
try Library search setup: Method 2 (see previous page). This
method allows you to scan through every code contained in
the remote's memory.
EN