Product Cleaning - Peg-Perego culla gran pagoda Instrucciones De Uso

8 Window B
The zips below the hood open another window level with
baby's head.
9 When both opened, the two windows ensure greater
ventilation and visibility.
10 The Pagoda Hood panorama window can also be opened
when the Pagoda Hood is pulled forwards.
11 IMPORTANT: close the panorama window before closing
the Pagoda Hood zip; this is done by keeping the Pagoda
Hood taut with one hand and closing the window with the
other.
12 The pram body's panorama windows can be opened and
closed via zips. Culla Gran Pagoda with both zips closed.
IMPORTANT: When the pram is moving, we recommend
closing the panorama window level with baby's head.
13 BACKREST ADJUSTMENT: pull the handle outwards and
rotate it clockwise to raise the backrest or anticlockwise to
lower it.
14 ADJUSTING THE FOOTREST: If necessary, the area
supporting the child's legs can be raised:
Pull the strap on the side under the pram body (Fig.1)
When the desired height has been reached, fasten it to the
bottom of the pram body (Fig.2). Raised footrest (Fig.3).
15 To return to the flat position:
Unfasten the strap from under the pram body (Fig.1),
press on the mattress (Fig.2) until it returns fully to the flat
position (Fig.3). The strap will withdraw automatically.
16 CARRY HANDLE: the handle bar is fitted with a carry
handle.
_ Before lifting the bassinet, ensure the built-in hood is
correctly fastened.
_ Before lifting the bassinet, make sure the hood is in the
correct position for transport.
_ Before unfastening and lifting the bassinet from the frame,
adjust the backrest to its lowest position.
17 To fasten the bassinet, position it on the frame and press
down with both hands until it clicks into place.
Always enable the brake on the frame before fastening and
unfastening the bassinet.
IMPORTANT: Ensure the bassinet is properly fastened.
18 To unfasten the bassinet, lift the two side levers on the
joints (Fig.1) and release it from the frame (Fig.2).
19 REMOVING THE HOOD: To remove the hood, unbutton the
6 buttons on the lower edge.
20 Press the buttons on the two attachments and remove the
hood.
21 Remove the two rigid supports.
22 REMOVING THE MATTRESS: Remove the mattress by pulling
it out from the headrest.
WARNING: reposition the mattress by slipping it in through
the headrest.
23 REMOVING THE LINING: Unfasten the internal fabric by
undoing the three side buttons on both sides (Fig.1).
Open the zip on the edge of the pram body (Fig.2).
24 Remove the fabric by pulling it from the headrest (Fig.3) and
then lifting it (Fig.4). Fabric removed correctly.
25 Do the opposite to reposition the lining.
When fastening the hood, ensure you insert the rigid
supports correctly. Insert the tube bearing the carry handle
into the hood's front slot, ensuring the handle is centred
correctly.
26 Finally, slip the second metal support into the hood' s inner slot.
27 Fasten the hood to the appropriate supports and fasten
the 6 buttons.
Padding cleaning instructions
Brush the fabric parts to remove dust.
• When washing, closely follow the instructions stated on
the label sewn into the cover.
• Do not use chlorine bleach.
• Do not iron.
• Do not dry clean.
• Do not remove stains with solvents and do not tumble dry.

Product cleaning

• This product requires a small amount of maintenance.
Cleaning and maintenance must only be carried out by adults.
• Keep all moving parts clean and if necessary lubricate
them with light oil.
• Clean the plastic parts periodically with a damp cloth. Do
not use solvents or similar substances.
• Brush the fabric parts to remove dust.
• Do not clean the polystyrene shock absorbing device with
solvents or other similar products.
15