Publicidad
Idiomas disponibles
Idiomas disponibles
PRODUCT SPECIFICATIONS
Maximum flow rate: 1.2 GPM (4.54 LPM) at 60 PSI
ASME A112.18.1/CSA B125
NSF/ANSI/CAN 61
Chrome, brushed nickel or matte black finish
INSTALLATION INSTRUCTIONS
1.
Shut off the water at the supply
valves under the sink or at the main
water supply. Disconnect the supply
lines. Remove the existing faucet
from the sink.
Clean and dry the surface area
where new faucet will be mounted.
2.
Ensure the gasket (2.1) is in place
on the bottom of the faucet body
(A). Apply a thin bead of silicone
sealant to the underside of the
gasket (2.1).
Insert the shanks (2.2) on the
faucet body (A) through the holes
in the sink. From underneath the
sink, thread the rubber washers
(AA) and mounting nuts (BB) onto
the shanks (2.2) on the faucet
body (A). Check the position of the
faucet and hand tighten until the
faucet is securely mounted.
NOTE: It is helpful to have a
second person hold the faucet
in place while tightening the
mounting nuts (BB).
3.
Attach one end of each of the water
supply lines onto the shanks (3.1)
on the faucet body (A), with hot
water on the left and cold water on
the right. Use 1/2 in. IPS faucet
connections (3.2) or supply line
coupling nuts (3.3) with 3/8 in. OD
ball-nose risers (3.4). NOTE: Do
not reuse existing supply lines.
When installing new water supply
lines, please refer to the supply
line manufacturer's installation
instructions. Tighten the supply line
connections using an adjustable or
basin wrench. Do not overtighten.
Attach each of the remaining ends
of the water supply lines to the hot
and cold shut-off valves and tighten
with a wrench. Do not overtighten.
4.
Remove the old pop-up drain
assembly. Clean all sink surfaces
to remove old putty and dirt before
installing the new drain assembly.
Remove the flange and upper
threaded portion (4.1) of the pop-up
drain assembly from the bottom
gasket (4.2), mounting nut (4.3)
and the lower portion of the pop-up
drain assembly (B).
1
2
A
2. 1
BB
AA
3
3.1
3.4
3.2
4
Washerless cartridges
Manufactured to include no more than 0.25% weighted average
lead content on wetted surfaces
5.
Insert the flange and upper portion
of the pop-up drain assembly (5.1)
into the sink hole (5.2).
NOTE: No sealants required.
Please only use the rubber
gasket under the drain flange.
6.
From underneath the sink, attach
the rubber gasket (6.1) and
mounting nut (6.2) onto the upper
portion of the pop-up drain
assembly (6.3). Then twist the
bottom of the pop-up drain
assembly (B) onto the upper
portion of the pop-up drain
assembly (6.3) and hand tighten.
Do not overtighten.
7.
After installation is complete,
remove the aerator (7.1) from the
spout (7.2) on the faucet body (A).
Turn on the water supply.
Check for leaks at all waterway
connections. If a leak occurs, gently
tighten the nut on the water
connection that is leaking. Fill the
sink with water to check the drain
for leaks. If water is leaking from
the drain, tighten the mounting nut
3.3
on the pop-up drain assembly (B).
After the pop-up drain has been
checked for leaks, empty the sink.
Run hot and cold water uninter-
rupted for at least one minute to
flush away any debris that could
cause damage to the internal
parts. Turn off the water and
reattach the aerator (7.1) onto the
spout (7.2) of the faucet body (A).
2
5
5.1
5.2
6
7
7.2
A
7.1
Homewerks.com
Publicidad
