Repair Service; Disposal And Recycling - stayer BJ120B Manual De Instrucciones

scale in angle 5 (there notches at 0 °, 45 ° and 90 °). Then
close the lever Tightening 3.
Start up
Note the mains voltage! The supply voltage
tion must match the on the nameplate of the
tool supply. Power tools marked 230V 220V
can work well.
The machine must only connected if the base
plate 33 has been firmly locked with the screw
32 and the metal cap 31 of safety precautions.
Before connecting the appliance, make sure
the mechanism to work properly Automatic re-
trieval engine unit:
Press Exit strawberry aganst the edge of a table,
eg visible until the cutter disk. By reducing pressure, the
cutter disk must be fully retracted on the motherboard.
Switching on / off
For connecting the machine, push forward the switch on
/ off 2 and press forward and downward to engage. to
switch off the machine, push back the switch / off switch
2, so that this skip to save energy desconexión.Para po-
sition, Only connect the machine when you go to use it.
General Instructions
Positioning milling
The vertical centerline 11 of the top brand for angles and
height stop indicates the center of milling (perpendicular
the milling cutter). The maximum width of milling the
indicate both brands top 10 of vertical adjustment in 9.
For positioning height serves as guidance horizontal
centerline 6 mark on the motherboard, as indicel center of
the milling cutter.
The arrow 13 in the housing of the power tool shows the
direction of rotation of the cutter disk.
Milling unions
Examples of these types of union finds in the illustrated
pages:
- Butt joint: with stop angles, with adjustment cap
vertically.
- Miter: with stop angles, with stopper vertical adjustment.
- Longitudinal and transverse Empalme: with stop
angles, vertical adjustment cap.
- Union of frames.
- Union of intermediate boards.
Selecting the cookie.
(see figure 9)
Milling narrow workpieces
Always use the top of vertical adjustment for milling
narrow parts 9. Note that the width marks Maximum drill
10 are not housed outside the workpiece work.
4. Maintenance and service instructions
Cleaning and Maintenance
Before any work on the tool power, remove the
ENGLISH
20
plug from the outlet.
Keep the power tool and cooling vents to work
effectively and safety.
Clean and oil the guides whenever necessary. use only oil
not forming resin (eg oil sewing machine).
Resetting the clamping lever If it must be you. Readjust
the clamping force levers 3 and 12. For this, loosen the
levers tightening and desatorníllelas.
Mount the clamping levers rotated at least 30°
counterclockwise to clockwise and then screw them.
Replacing a damaged cable should be performed by
Stayer or a technical service Power Tool Stayer authorized
to to ensure the safety of the appliance.

5.2 Repair service

Our after-sales service responds to your questions
conceming maintenance and repair ofyour product as well
as spare parts.
Exploded views and information on spare parts can also
be found under: info@grupostayer.com
Our customer consultants answer your questions
conceming best buy, application and adjustment of
productsand accessories.

Disposal and recycling

We recommend that the power tools, accessories and
packaging are subject to a recovery process that respects
the environment.
Only for EU countries:
Do not dispose of power tools into household waste!
According the European Guideline 2012/19/
UE for Waste Electrical and Electronic
Equipment and its implementation into national
right,power tools that are no longer usable
must be collected separately and disposed of
in an environmentally correct manner.
Subject to change wlthout notlce.
5. Regulations
Technical Data
= Power
= Giros empty
= Vertical adjustment
= Diameter of strawberry
ANGLED
CUTS
= Court inclined
0-90º
= Depth of cut
= Weight
kg
= Protection class
L = Sound power level
WA
L
= Sound pressure level
WA
= Vibrations
20