Publicidad
Idiomas disponibles
Idiomas disponibles
English
Mounting Non‑Hubbed Wheels (Fig. C)
WARNING: Failure to properly seat the flanges and/or
wheel could result in serious injury (or damage to the
tool or wheel).
CAUTION: Included flanges must be used with
Type 27 depressed center grinding wheels. See the
Accessories Chart for more information.
WARNING: A closed, two‑sided cutting wheel guard
is required when using abrasive cutting wheels. Not
available for this grinder.
WARNING: Use of a damaged flange or guard or
failure to use proper flange and guard can re sult in
injury due to wheel breakage and wheel contact. See
the Accessories Chart for more information.
WARNING: Do not use Type 1/41 cutting wheels on
this grinder. Only use wheels 1/8" minimum thickness.
Depressed center Type 27 grinding wheels must be used
with included flanges.
1. Place the tool on a table, guard up.
2. Install the backing flange
center (pilot) facing the wheel. Press the backing flange
into place.
3. Place wheel
against the backing flange, centering the
19
wheel on the raised center (pilot) of the backing flange.
4. While depressing the spindle lock button and with the
hex depressions facing away from the wheel, thread the
locking flange
6
.
5. While depressing the spindle lock button, tighten the
locking flange
by hand or using the wrench supplied.
6
(Only use a locking flange if it is in perfect condition.)
Refer to Accessory Chart to see flange details.
6. To remove the wheel, reverse the above procedure.
Over 1/8" (3.17 mm)
Locking flange
Backing Flange
Mounting Sanding Backing Pads (Fig. D)
WARNING: Use only backing pads that are rated for at
least equal to the rated speed marked on the tool.
WARNING: Failure to properly seat the clamp nut and/
or pad could result in serious injury (or damage to the
tool or wheel).
WARNING: Proper guard must be reinstalled for
grinding wheel, sanding flap disc, wire brush or
wire wheel applications after sanding applications
are complete.
nOTE: Use of a guard with sanding discs that use backing
pads, often called fiber resin discs, is not required. Since a
10
5
on spindle
3
with the raised
wheels
guard is not required for these accessories, the guard may or
may not fit correctly if used.
1. Place or appropriately thread backing pad
the spindle.
2. Place the sanding disc
3. While depressing spindle lock button
sanding clamp nut
22
hub on the clamp nut into the center of san ding disc and
backing pad.
4. Tighten the clamp nut by hand. Then depress the spindle
lock button while turning the sanding disc until the
sanding disc and clamp nut are snug.
5. To remove the wheel, grasp and turn the backing
pad and sanding pad while depressing the spindle
lock button.
Mounting and Removing Hubbed
Wheels (Fig. A)
Hubbed wheels with 5/8"‑11 thread install directly on the
spindle. Thread of accessory must match thread of spindle.
1. Remove backing flange by pulling away from tool.
2. Thread the wheel on the spindle
3. Depress the spindle lock button
tighten the hub of the wheel.
4. Reverse the above procedure to remove the wheel.
NOTICE: Failure to properly seat the wheel before
turning the tool on may result in damage to the tool
or the wheel.
Mounting Wire Cup Brushes and
Wire Wheels (Fig. A)
WARNING: Failure to properly seat the brush/wheel
could result in serious injury (or damage to the tool
or wheel).
CAUTION: To reduce the risk of personal injury,
wear work gloves when handling wire brushes
and wheels. They can become sharp.
CAUTION: To reduce the risk of damage to the
tool, wheel or brush must not touch guard when
mounted or while in use. Undetectable damage
could occur to the accessory, causing wires to fragment
from accessory wheel or cup.
Wire cup brushes or wire wheels install directly on the
threaded spindle without the use of flanges. Use only wire
brushes or wheels provided with a 5/8"‑11 threaded hub.
These accessories are available at extra cost from your local
dealer or authorised service center.
1. Place the tool on a table, guard up.
2. Thread the wheel on the spindle by hand.
3. Depress spindle lock button
hub of the wire wheel or brush to tighten the wheel.
4. To remove the wheel, reverse the above procedure.
NOTICE: To reduce the risk of damage to the tool,
properly seat the wheel hub before turning the tool on.
Prior to Operation
•
Install the guard and appropriate disc or wheel. Do not
use excessively worn discs or wheels.
on
20
21
on the backing pad.
, thread the
4
on spindle, piloting the raised
by hand.
3
and use a wrench to
4
4
and use a wrench on the
Publicidad
