Publicidad
Idiomas disponibles
Idiomas disponibles
WARNING: Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
WARNING: To reduce the risk of injury, read the
instruction manual.
Contents
•
Laser Information
•
User Safety
•
Batteries and Chargers
•
Operating Tips
•
Turning the Laser ON
•
Checking Laser Accuracy
•
Field Calibration Check
•
Using the Laser
•
Maintenance
•
Troubleshooting
•
Accessories
•
Service and Repairs
•
Warranty
•
Specifications
LASER INFORMATION
The DCLE34031 3x360 Laser is a Class 2 laser product. It is a
self‑leveling laser tool that can be used for horizontal (level)
and vertical (plumb) alignment projects.
This product complies with 21 CFR 1040.10 and 1040.11
except for conformance with IEC 60825‑1 Ed. 3., as described
in Laser Notice No. 56, dated May 8, 2019.
-
Conforms to UL STDS 61010‑1 & 2595
-
Certified to CSA STD C22.2 No. 61010‑1
Supplier's Declaration of Conformity
47 CFR § 2.1077 Compliance Information
Unique Identifier: DCLE34031
Responsible Party – U.S. Contact Information
D
WALT
e
701 East Joppa Road
Towson, Maryland 21286
www.D
WALT.com
e
FCC Compliance Statement
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio and television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment
and receiver.
•
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician
for help.
ISED Compliance Statement
This device contains license‑exempt transmitter(s)/receiver(s)
that comply with Innovation, Science, and Economic
Development Canada's license‑exempt RSS(s). Operation is
subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including
interference that may cause undesired operation of
the device.
USER SAFETY
Safety Guidelines
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to
these symbols.
DANGER: Indicates an imminently hazardous
situation which, if not avoided, will result in death or
serious injury.
WARNING: Indicates a potentially hazardous
situation which, if not avoided, could result in death or
serious injury.
CAUTION: Indicates a potentially hazardous
situation which, if not avoided, may result in minor or
moderate injury.
NOTICE: Indicates a practice not related to
personal injury which, if not avoided, may result in
property damage.
If you have any questions or comments about
this or any D
call 1‑800‑4‑D
or go to www.D
WARNING: Never modify the tool or any part of it.
Damage to the laser or personal injury could result.
WARNING: Read and understand all instructions.
Failure to follow the warnings and instructions may
result in electric shock, fire and/or serious injury.
SAVE THESE INSTRUCTIONS
WALT tool,
e
WALT (1‑800‑433‑9258)
e
WALT.com.
e
English
7
Publicidad
