Publicidad
Idiomas disponibles
Idiomas disponibles
en
ENGLISH
Accessories must be stored and handled with care
in accordance with the manufacturer's instructions.
Secure small workpieces, for example by clamping
them in a vice.
The workpiece must lay flat and be secured against
slipping, e.g. using clamps. Large workpieces must
be sufficiently supported.
If accessories with threaded inserts are used, the
end of the spindle may not touch the base of the
hole on the sanding tool. Make sure that the thread
in the accessory is long enough to accommodate
the full length of the spindle. The thread in the
accessory must match the thread on the spindle.
See page 4 and chapter 14. Technical
Specifications for more information on the spindle
length and thread.
Impurities that manage to enter the
machine may block the switching
mechanism. This is why it is necessary when the
machine is running to blow compressed air through
the rear ventilation slots of the machine regularly,
frequently and thoroughly. Here, the machine must
be held firmly.
Damaged, eccentric or vibrating tools must not be
used.
Avoid damage to gas or water pipes, electrical
cables and load-bearing walls (building structure).
When using the machine outdoors:
Connect an FI circuit-breaker with max. release
current (30 mA) upstream
Ensure that the spot where you wish to work is free
of power cables, gas lines or water pipes (e.g.
using a metal detector).
Pull the plug out of the socket before making any
adjustments, converting or servicing the machine.
A damaged or cracked side handle must be
replaced. Never operate the machine with a
defective additional handle.
A damaged or cracked safety guard must be
replaced. Never operate a machine with a defective
safety guard.
Only use accessories that are surmounted by
brushes of the safety guard.
Additional Warnings:
WARNING
drilling, and other construction activities
contains chemicals known to cause cancer,
birth defects or other reproductive harm. Some
examples of these chemicals are:
• Lead from lead-based paints,
• Crystalline silica from bricks and cement and
other masonry products, and
• Arsenic and chromium from chemicallytreated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
8
California Prop 65 08_2018
Some dust created by power
sanding, sawing, grinding,
specially designed to filter out microscopic
particles.
Observe the relevant guidelines for your material,
staff, application and place of application (e.g.
occupational health and safety regulations,
disposal).
Collect the generated particles at the source, avoid
deposits in the surrounding area.
Use suitable accessories for special work (see
chapter 11.), thus less particles enter the
environment in an uncontrolled manner.
Use a suitable extraction unit.
Reduce dust exposure with the following measures:
- For efficient dust collection, use a suitable
Metabo M-class vacuum cleaner together
with this power tool.
- Do not direct the escaping particles and the
exhaust air stream at yourself or nearby persons
or on dust deposits
- Use an extraction unit and/or air purifiers
- Maintain good ventilation of the workplace and
keep clean using a vacuum cleaner Sweeping or
blowing will stir up dust
- Vacuum or wash your protective clothing Do not
blow, beat or brush.
Symbols on the tool:
..........Class II Construction
V..............volts
A..............amperes
Hz............hertz
W.............watts
Ø .............max. diameter of the accessory
.../min ......revolutions per minute
rpm..........revolutions per minute
~ ..............alternating current
n ............. rated speed
4. Overview
See pages 2 and 3.
1 Spindle locking button
2 Side handle
3 Sliding on/off switch
4 Handle
5 Electronic signal indicator
6 Speed adjustment wheel
7 Spindle
8 Support flange
9 Diamond cup wheel*
10 Clamping nut
11 two-hole spanner
12 Support plate *
13 Fibre grinding disc*
14 Adjusting nut of backing pad *
15 Cling-fit backing pad*
16 Cling-fit grinding disc*
17 Lever
18 Safety cover
Publicidad
