Technical Parameters; Environmental Protection - GRAPHITE 58G030 Traducción Del Manual Original

• Clean the device with brush or delicate cloth.
• Store the device in a dry place, beyond reach of children.
• Store the device with the battery removed.
REPLACEMENT OF CUTTING PARTS
The grass trimmer is supplied with 20 spare cutting parts that are
attached to the auxiliary handle. Use only recommended cutting
parts.
• Put larger hole of the cutting part (12) over the pin (22) of the
head (13) and pull outwards, so the pin (22) is in the smaller hole
of the cutting part (12) (fig. L).
• Repeat the action for the second cutting part.
• Removal of the cutting part (12) is similar to installation, only the
sequence of actions is reversed.
All defects should be repaired by service workshop authorized by
the manufacturer.

TECHNICAL PARAMETERS

RATED PARAMETERS
Cordless Grass Trimmer 58G030
Parameter
Battery voltage
Spindle rotational speed with no load
Cutting width
Polymer blades
Number of blades attached to the
head
Handle length adjustment
Protection class
Weight
Year of production
58G030 defines type and indication of the device
Graphite Energy+ System Battery
Parameter
Battery
Battery voltage
Battery type
Battery capacity
Ambient temperature range
Charging time for charger 58G002
Weight
Year of production
Graphite Energy+ System Charger
Parameter
Charger type
Supply voltage
Power supply frequency
Charging voltage
Max. charging current
Ambient temperature range
Value
18 V DC
9000 min
-1
254 mm
88,5 mm
2
1,1 ÷1,4 m
III
1,8 kg
2020
Value
58G001 58G004
18 V DC 18 V DC
Li-Ion Li-Ion
2000 mAh 4000 mAh
4 C – 40 C 4 C – 40 C
0 0 0 0
1 h 2 h
0,400 kg 0,650 kg
2020 2020
Value
58G002
230 V AC
50 Hz
22 V DC
2300 mA
4 C – 40 C
0 0
15
Charging time of the battery 58G001
Charging time of the battery 58G004
Protection class
Weight
Year of production
NOISE LEVEL AND VIBRATION PARAMETERS
Sound pressure
Sound power
Vibration acceleration (main
handle)
Vibration acceleration (auxiliary
handle)
Noise and vibration information
Noise produced by the device is defined with: level of produced
sound pressure L and level of sound power L
PA
measurement uncertainty). Vibrations produced by the device
are defined with vibration acceleration value a
measurement uncertainty).
Sound pressure L , sound power L
PA
specified in this manual have been measured in accordance with the
standard EN 60335-1:2012; EN 50636. Specified vibration level a
be used to compare tools and for initial evaluation of exposition to
vibrations.
Specified vibration level is typical only for the main applications
of the device. When the device is used for other purposes or with
different working tools, the vibration level may change. Insufficient
or too rare maintenance may increase vibration level. The
abovementioned factors may lead to higher exposure to vibrations
during whole working time.
In order to precisely define exposure to vibrations, include periods
when the device is switched off and when it is switched on but not
used for working. Once all factors have been carefully considered,
total exposition to vibrations may be significantly lower.
To protect the user from results of exposure to vibrations, use
additional safety measures such as: device and working tool periodic
maintenance, proper hand temperature conditions, good work
organisation.

ENVIRONMENTAL PROTECTION

Electrical equipment must not be disposed off
with household waste and, instead, should be
utilized at appropriate facilities. Information
on utilization can be provided by the product
vendor or the local authorities. Waste electrical
and electronic equipment contains substances
that are not neutral to the natural environment.
Equipment that is not recycled constitutes a
potential hazard to the environment and to
human health.
Storage batteries/batteries must not be disposed
with domestic waste, put in a fire or into the
water. Damaged or used up storage batteries
must be properly recycled in compliance with the
current directive pertaining to disposal of storage
batteries and batteries.
Li-Ion
* Right to introduce changes is reserved.
"Grupa Topex Spółka z ograniczoną odpowiedzialnością" Spółka komandytowa
with seat in Warsaw at ul. Pograniczna 2/4 (hereinafter Grupa Topex) informs,
that all copyrights to this instruction (hereinafter Instruction), including, but not
limited to, text, photographies, schemes, drawings and layout of the instruction,
1 h
2 h
II
0,300 kg
2020
L = 79,5 dB(A) K=3dB(A)
PA
L = 91,9 dB(A) K=2,23dB(A)
WA
a = 1,453 m/s K=1,5 m/s
2 2
h
a = 3,224 m/s K=1,5 m/s
2 2
h
(where K is
WA
(where K is
h
and vibration acceleration a
WA h
can
h