Publicidad
Idiomas disponibles
Idiomas disponibles
Preparing Spray Handle (Fig. A)
IMpoRTaNT: Before turning on the pressure washer unit,
disengage the trigger lock‑off
1. Disengage the trigger lock‑off
2. Squeeze the trigger
7
purge the system of air.
3. If air is still found in the water stream, continue to run
water through the spray handle.
Water Connection
WARNING: According to the applicable
regulations, the appliance must never be
used on the drinking water network
without a system seperator. Use a system
seperator as per IEC 61770 Type BA.
Water flowing through a system seperator is not
considered drinkable.
•
Comply with the regulations of your water
supply company.
•
All connecting hoses must have properly sealed joints.
•
Make sure the supply hose is at least 12.7 mm in
diameter and is reinforced.
•
The appliance should never be used on the drinking
water supply without a backflow valve. Water that has
passed the backflow valve is considered undrinkable.
Cleaning a Surface (Fig. A)
1. To start the pressure washer, press the ON button
2. Confirm that the water faucet is open or use any other
water source so that water will be supplied to the
pressure washer unit.
3. The best angle for spraying water against a cleaning
surface is 45 °.
Spraying head on tends to cause dirt particles to
-
imbed in the surface.
-
When working on vertical surfaces, it is best to
apply detergent starting at the bottom and working
upwards which will prevent the detergent from
sliding down and causing streaks.
4. To disengage the spray handle, release the trigger.
NoTE: Excessive pump pressure may be the result of a
clogged nozzle. Always turn OFF the pressure washer
unit and unplug the unit before attempting to unclog
a nozzle.
Detergents (J1, J2, J3, J4)
For steps on attaching the detergent/soap bottle,
please refer to attaching soap Bottle under Assembly
and Adjustments.
The use of detergents can dramatically reduce cleaning time
and assist in the removal of difficult stains. Some detergents
have been customized for pressure washer use on specific
cleaning tasks.
The cleaning power of detergents comes from applying
them to a surface and giving the chemicals time to break
6
and squeeze the trigger
6
.
. Hold the trigger for 30 seconds to
down the dirt and grime. Detergents work best when applied
at low pressure.
The combination of chemical action and high pressure
7
.
rinsing is very effective.
On vertical surfaces, apply the detergent starting at the
bottom and work your way upward. This will prevent the
detergent from sliding down and causing streaks. High
pressure rinsing should also progress from the bottom
to top. On particularly tough stains, it may be necessary
to use a brush in combination with detergents and high
pressure rinsing.
Moving the Pressure Washer (Fig. A)
1. Turn OFF the pressure washer unit
button
10
2. Point the spray wand
trigger
7
3. When the spray wand is completely empty, lift the
pressure washer by the handle
Shutdown (Fig. A, D)
1. Turn OFF the pressure washer unit
button
10
2. Turn OFF water at the faucet or disconnect from any
other water source.
3. Discharge residual pressure by squeezing the trigger
until no more water comes out of the spray wand
4. Engage the spray trigger lock‑off
9
.
5. Disconnect the garden hose
intake
12
6. Disconnect the high pressure hose
pressure water outlet
Self Priming (Fig. A, C, D, K1, K2, K3, K4)
1. Connect the inlet hose to the pressure washer.
Refer to attaching Garden hose under Assembly
and Adjustments.
2. Place the free end of the hose with filter attached into the
alternative water source (e.g. bucket, etc.)
3. Connect the high pressure hose to the spray handle.
Please refer to attaching high pressure hose under
Assembly and Adjustments.
4. Plug the pressure washer unit into a power source.
5. Actuate the pressure washer by pressing the ON
button
9
6. Turn OFF the pressure washer as soon as water is
spraying out of the outlet tube of the unit.
7. Unplug the pressure washer unit from the power source.
8. Assemble the high pressure hose to the high pressure
water outlet.
9. Plug the pressure washer unit into a power source.
10. Actuate the pressure washer by pressing the ON
button
9
11. Actuate the trigger of the spray handle to start
cleaning work.
and then turn OFF the water supply.
2
in a safe direction and pull the
to release remaining water pressure.
11
and unplug the cord from the outlet.
6
26
from the water
.
13
and drain hose.
.
.
ENGlIsh
by pressing the OFF
8
.
8
by pressing the OFF
7
2
.
.
1
from the high
27
Publicidad
