Replacing The Filter; Customer Service - DrBrowns AC178-INTL Instrucciones De Uso

REPLACING THE FILTER

CAUTION: Unplug from outlet and allow to cool for 60 minutes before
replacing filter�
Replace the filter every six months of regular use for optimal performance�
Follow the steps below:
1� The filter is located at the bottom of the base� Gently squeeze the latches on the filter
1
cover to remove it�
2
2� Remove and replace the filter, ensuring the pull tab is still visible on top of the filter�
3
3� Snap the filter cover back into position�
Note: Filter must always be used to ensure proper performance�
4
D
C
B
A
4
WARRANTY
This appliance is warranted against defective material or workmanship for a period of
one year from the date of purchase� Any defective part will be repaired or replaced at no
charge if it has not been tampered with and appliance has been used according to these
printed instructions� This warranty gives you specific legal rights as well as other rights
which vary from state to state�
This warranty does not cover a defect that has been caused by negligence, accidents or
improper use of the appliance� To keep your Dr� Brown's™ Bottle Sterilizer and Dryer in
good condition and retain your warranty, USE ONLY AS DIRECTED�

CUSTOMER SERVICE

If you experience unsatisfactory operation or have questions/comments,
your local Dr� Brown's distributor� See drbrownsbaby�com/distributors to find your local
contact�
3
B
A
DESIGN UNITS: MILLIMETERS
TOLERANCES UNLESS NOTED:
NO PLACE:
ONE PLACE:
TWO PLACE:
THREE PLACE:
ANGLE:
ANGLE:
To purchase replacement filters, contact your local distributor�
3
2
2 1
THIS DRAWING AND RELATED 3D CAD DATA
HANDI-CRAFT COMPANY
CONTAINS PROPRIETARY INFORMATION THAT
ARE THE PROPERTY OF
X 2.5
HANDI-CRAFT CO. AND ARE NOT TO BE
.X 0.5
COPIED OR USED WITHOUT THE PERMISSION
.XX 0.25
OF HANDI-CRAFT CO.
.XXX 0.13
X 0.5
INTERPET PER ASME Y14.5-1994 DRAWN
.X 0.25
OTHER HANDI-CRAFT ENGINEERING
2 f ilters are included�
ENG APPR.
STANDARDS MAY APPLY
THIRD ANGLE
SOLIDWORKS 3D
MFG/Q.A APPR.
PROJECTION
2
DESIGN UNITS: MILLIMETERS RBW 15JUL19
DRAWN HANDI-CRAFT COMPANY
TOLERANCES UNLESS NOTED:
ENG APPR.
NO PLACE: X 2.5
4433 FLYER AVE. ST. LOUIS MO. 63116, USA
ONE PLACE: .X 0.5 MFG/Q.A APPR.
TWO PLACE: .XX 0.25
TITLE:
THIS DRAWING AND RELATED 3D CAD DATA
THREE PLACE: .XXX 0.13
FILTER REPLACEMENT
CONTAINS PROPRIETARY INFORMATION
ANGLE: X 0.5
THAT ARE THE PROPERTY OF
ANGLE: .X 0.25
HANDI-CRAFT CO. AND ARE NOT TO BE
COPIED OR USED WITHOUT THE
PERMISSION OF HANDI-CRAFT CO.
DO NOT SCALE DRAWING
INTERPET PER ASME Y14.5-1994 SIZE C DWG. NO.
THIRD ANGLE OTHER HANDI-CRAFT ENGINEERING
STANDARDS MAY APPLY
PROJECTION
MATERIAL
SOLIDWORKS 3D SCALE: 1:1
2 1
D
C
B
4433 FLYER AVE. ST. LOUIS MO. 63116, USA
MATERIAL
RBW 15JUL19
DO NOT SCALE DRAWING
A
REV. 1
SHEET 1 OF 1
please contact
1
TITLE:
FILTER AND COVER
SIZE DWG. NO. REV.
A 1
SCALE: 1:2 SHEET 1 OF 1
1
7
B
A