Publicidad
Idiomas disponibles
Idiomas disponibles
English
13. The tines are keyed and only correctly install one way so
that the hole for the clip pin is exposed as shown in fig. X.
14. Wearing gloves, slide the tine onto the tine shaft and
install the washer and then the clip pin.
Preventing Corrosion
Fertilizers and other garden chemicals contain agents that
greatly accelerate the corrosion of metals. If you use the
tool in areas where fertilizers or chemicals have been used,
the tool should be cleaned immediately afterwards. Wipe
all exposed parts with a damp cloth. You may lubricate only
metal parts with a light petroleum based oil.
When cleaning, DO NOT immerse tool in water or squirt it
with a hose.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Your CRAFTSMAN power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Accessories
WARNING: Since accessories, other than those
offered by CRAFTSMAN, have not been tested with
this product, use of such accessories with this product
could be hazardous. To reduce the risk of injury, only
CRAFTSMAN recommended accessories should be used
with this product.
Recommended accessories for use with your product are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact CRAFTSMAN call 1‑888‑331‑4569.
10
Versatrack™ (Fig. R)
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑upcan cause injury.
WARNING: To reduce the risk of serious personal injury,
do not use a damaged Versatrack™ integral hang hook
or Versatrack™ Trackwall. A damaged Versatrack™
integral hang hook or Versatrack™ Trackwall will not
support the weight of the tool.
WARNING: To reduce the risk of serious personal injury,
DO NOT suspend tool overhead or suspend objects
from the integral hang hook. ONLY suspend tool on the
Versatrack™ Trackwall using the integral hang hook.
WARNING: The Versatrack™ integral hang hook
is intended to mount the tool onto a Versatrack™
Trackwall rail. Do not use the integral hang hook to
mount the tool to any other surface.
WARNING: The Versatrack™ integral hang hook is not
a belt hook.
WARNING: When hanging objects on a Versatrack™
Trackwall rail, adequately space the tools in order to not
exceed 75 lb (35 kg) per linear foot.
WARNING: Before using the tool make sure that
the Versatrack™ integral hang hook is returned to its
original position.
iMPORTAnT: Versatrack™ accessories mount compatible
tools securely to the Versatrack™ Trackwall system.
1. Turn tool off, remove the battery pack and
remove accessories.
2. Flip or pull open the integral hang hook
when locked into position.
3. Mount the integral hang hook to the
Versatrack™ Trackwall.
nOTE: Versatrack™ accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact CRAFTSMAN, call 1‑888‑331‑4569.
21
. It clicks
Publicidad
