Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
1) Connect the DMX input (10) to the DMX output
of the light controller.
2) Connect the DMX output (13) to the DMX input
of the following light effect unit; connect its out-
put again to the input of the following unit, etc.
until all light effect units have been connected in
a chain.
3) To prevent interference in signal transmission (in
case of long cables or a multitude of units con-
nected in series), terminate the DMX output of
the last DMX unit in the chain with a 120 Ω resis-
tor (> 0.3 W): Connect a corresponding termi-
nating plug (e. g. DLT-123 from "img Stage
Line") to the output jack.
6.2 Setting the DMX start address and
the number of DMX channels
For controlling the light effect unit with a light con-
troller, it is necessary to set the DMX start address
for the first DMX channel. If e. g. address 17 on the
controller is provided for controlling the pan of the
head, set the start address 17 on the TWIST-50LED.
The other functions of the TWIST-50LED are
automatically assigned to the 10 following channels
(in this example 18 – 27). In this example, the next
possible start address for the following DMX-con-
trolled unit would be address 28. (In the 8-channel
mode, only 8 DMX channels are used, i. e. the next
possible start address for the following DMX-con-
trolled unit would be address 25.)
1) Set the DMX start address:
a) Press the button MENU (7) once so that the
display (9) shows
b) Press the button ENTER. The address
adjusted starts flashing on the display.
c) Press the button
To memorize, press the button ENTER.
2) Set the number of DMX channels to be used to
control the moving head:
a) Press the button MENU repeatedly until the
display shows
b) Press the button ENTER. The number of
DMX channels starts flashing on the display.
c) Press the button
DMX channels (
press the button ENTER.
3) To exit the setting mode, keep the button MENU
pressed until the LED DMX or MASTER (6)
lights up or wait for one minute and do not press
any button.
4) Once the control signals of the DMX controller
are received, the red LED DMX (6) lights up and
.
or
to set the address.
(Channel Mode).
or
to set the number of
or
). To memorize,
the display shows the start address. Now the
TWIST-50LED can be operated with the DMX
controller.
To activate the light beam, set DMX channel
7 or 3* to a DMX value between 8 and 15 or to
255 and set the desired brightness via DMX
channel 6 or 7*,
*channel number for the 8-channel mode
7 Additional Functions
7.1 Offset correction
For fine adjustment of the head position and of the
colour wheel and gobo wheel, settings for offset
correction can be made. For synchronous control
of several TWIST-50LED moving heads via the
same DMX addresses, this procedure is used e. g.
to minimize deviations in the direction of the light
beam.
1) Keep the button ENTER (7) pressed for approx-
imately 2 seconds until the display changes to
show
.
2) Press the button MENU,
required function:
fine adjustment for the pan of the head
fine adjustment for the tilt of the head
adjustment of the rotation angle for the
colour wheel
adjustment of the rotation angle for the
gobo wheel
3) Press the button ENTER to activate the function.
4) Press the button
5) To memorize, press the button ENTER. To
switch to another function, press the button
MENU,
or
.
6) To return to the previous operating mode, keep
the button MENU pressed for one second or wait
for one minute and do not press any button.
7.2 Self-test
To test the moving head, a short test program is
available. To start it:
1) Press the button MENU (7) repeatedly until the
display (9) shows
2) Press the button ENTER to start the test run. At
the end of the test, the light beam is deactivated
and the head returns to its starting position.
3) To return to the previous operating mode, keep
the button MENU pressed for one second or wait
for one minute and do not press any button.
chapter 9.1.
or
to select the
or
to change the setting.
.
GB
17
Publicidad
Capítulos
Tabla de contenido
