Truper HIDR-1/2X24 Manual De Instrucciones
Ocultar thumbs
Ver también para HIDR-1/2X24:
- Manual de instrucciones (25 páginas) ,
- Instructivo (10 páginas)
Manuales relacionados para Truper HIDR-1/2X24
Resumen de contenidos para Truper HIDR-1/2X24
- Página 1 Manual Hydropneumatic Simultaneous Pressure Boosting Water Connections System Applies for: Codes Models 10077 HIDR-1/2X24 12254 HIDR-1/2X50 Read the user’s manual thoroughly CAUTION before operating this tool.
-
Página 2: Tabla De Contenido
Parts Installation Keep this manual for future references. Pressure Switch The illustrations in this manual are for reference only. They might be different from the real tool. Start Up Maintenance Troubleshooting Notes Authorized Service Centers Warranty Policy HIDR-1/2X24 HIDR-1/2X50 ENGLISH... -
Página 3: Technical Data
Technical data HIDR-1/2X24 HIDR-1/2X50 Code 10077 12254 Description Hydropneumatic Pressure Boosting System Voltage 127 V Frequency 60 Hz Current 6.5 A Speed 3 400 RPM Inlet and Outlet Diameter 1” x 1” Maximum Suction Depth 29.5 ft Maximum Height / Maximum Value of... -
Página 4: General Power Tool Safety Warnings
General Power Tools Safety Warnings WARNING! Read carefully all safety warnings and instructions listed below. Failure to comply with any of these warnings may result in electric shock, fire and / or severe damage. Save all warnings and instructions for future references. -
Página 5: Safety Warnings For Hydropneumatic Equipment
Safety Warnings for Hydropneumatic Equipment CAUTION • Do not set up the equipment outdoors Appropriate Use or close to wet areas. WARNING • Do not install the device in areas • The equipment is a stationary device designed to pump where there is danger of explosion or in the vicinity of clean neutral liquids that do not contain suspended combustible liquids or gases. -
Página 6: Parts
Parts Pressure Water switch outlet (Pressurestat) Pressure Enclosed power motor gauge with external ventilation Purge Jet type pump Water inlet Drain Tank Pump - Tank interconnection hose Brackets to fix the equipment ENGLISH... -
Página 7: Installation
Installation Mounting • The set-up place for the equipment shall be dry and no exposed to weather with enough air flowing to get adequate ventilation (A). The environment temperature shall not exceed (104 °F). • Use bolts to fix the equipment to a concrete base to prevent vibration (B). The hydro pneumatic equipment shall be set horizontally to assure perfect functioning. -
Página 8: Pressure Switch
Pressure Switch • The hydro pneumatic machine is equipped with a pressure switch (pressurestat) that turns on the motor when the tank pressure is equal or lower than the starting pressure. • The pressurestat turns off the motor when the pressure inside the tank increases up to the stopping pressure. CAUTION The pressurestat is calibrated in the factory to correct the starting and closing pressure. -
Página 9: Maintenance
Maintenance • The hydro pneumatic equipment does not require maintenance only if taking the following caution measures: • When there is risk of freezing empty the pump completely removing the drain cap (B). Remember to purge the pump before starting it back. •... -
Página 10: Notes
Notes ENGLISH... -
Página 11: Authorized Service Centers
In the event of any problem contacting a Authorized Service Center, please see our webpage www.truper.com to get an updated list, or call our toll-free numbers 800 690-6990 or 800 018-7873 to get information about the nearest Service Center. DE TODO PARA LA CONSTRUCCIÓN FIX FERRETERÍAS... -
Página 12: Warranty Policy
. Transportation costs resulting from compliance of this warranty will be covered by For questions or comments, call 800-690-6990. Made in China. Imported by Truper S.A. de C.V. Parque Industrial 1, Parque Industrial Jilotepec, Jilotepec, Edo. de Méx. C.P. 54257 Stamp of the business.