Descargar Imprimir esta página
Truper HIDR-1X100 Manual
Ocultar thumbs Ver también para HIDR-1X100:

Publicidad

Enlaces rápidos

Manual
Hydropneumatic
Pressure
Boosting
System
Applies for:
Codes
Models
12255
HIDR-1X100
12257
HIDR-1-1/2X150
CAUTION
Read the user's manual thoroughly
before operating this tool.
9
15
and
Simultaneous
Water Connections

Publicidad

loading

Resumen de contenidos para Truper HIDR-1X100

  • Página 1 Manual Hydropneumatic Simultaneous Pressure Water Connections Boosting System Applies for: Codes Models 12255 HIDR-1X100 12257 HIDR-1-1/2X150 Read the user’s manual thoroughly CAUTION before operating this tool.
  • Página 2: Tabla De Contenido

    Parts Installation Keep this manual for future references. Start Up The illustrations in this manual are for reference only. They might be different from the real tool. Maintenance Troubleshooting Notes Authorized Service Centers Warranty Policy HIDR-1X100 HIDR-1-1/2X150 ENGLISH...
  • Página 3: Technical Data

    Technical Data HIDR-1x100 HIDR-1-1/2x150 Code 12255 12257 Description Hydropneumatic pressure boosting system Voltage 127 V Frequency 60 Hz Current 9.5 A 11 A Speed 3 400 RPM Inlet and Outlet Diameter 1” x 1” Maximum Suction Depth 30 ft Maximum Height / Maximum Value of...
  • Página 4: General Power Tool Safety Warnings

    General Power Tools Safety Warnings WARNING! Read carefully all safety warnings and instructions listed below. Failure to comply with any of these warnings may result in electric shock, fire and / or severe damage. Save all warnings and instructions for future references.
  • Página 5: Safety Warnings For Hydropneumatic Equipment

    Safety Warnings for Hydropneumatic Equipment CAUTION • Do not set up the equipment outdoors Appropriate Use or close to wet areas. WARNING • Do not install the device in areas • The equipment is a stationary device designed to pump where there is danger of explosion or in the vicinity of clean neutral liquids that do not contain suspended combustible liquids or gases.
  • Página 6: Parts

    Parts Closed electric motor Pressurestat with external ventilation Pressure gauge Jet type pump Purge Water inlet Drain Pump-Tank Inter connection Hose Tank Equipment Fixing Supports Water outlet ENGLISH...
  • Página 7: Installation

    Installation Mounting • The set-up place for the equipment shall be dry and no exposed to weather with enough air flowing to get adequate ventilation (A). The environment temperature shall not exceed 104 °F. • Use bolts to fix the equipment to a concrete base to prevent vibration (B). The hydro pneumatic equipment shall be set horizontally to assure perfect functioning.
  • Página 8: Start Up

    Start Up Purge • The first time you start the hydro pneumatic equipment, or after a long period of inactivity, or when air enters into the system, fill the pump with clean water before starting • Remove the purge cap (A) and fill with water up to the orifice level.
  • Página 9: Troubleshooting

    Troubleshooting Problem Cause Solution The motor does not • There is no power. • Check connections and voltage values. start . • The impeller is stuck. • Remove the fan cover and turn the shaft to release it. The motor turns but is •...
  • Página 10: Notes

    Notes ENGLISH...
  • Página 11: Authorized Service Centers

    In the event of any problem contacting a Authorized Service Center, please see our webpage www.truper.com to get an updated list, or call our toll-free numbers 800 690-6990 or 800 018-7873 to get information about the nearest Service Center. DE TODO PARA LA CONSTRUCCIÓN FIX FERRETERÍAS...
  • Página 12: Warranty Policy

    . Transportation costs resulting from compliance of this warranty will be covered by For questions or comments, call 800-690-6990. Made in China. Imported by Truper S.A. de C.V. Parque Industrial 1, Parque Industrial Jilotepec, Jilotepec, Edo. de Méx. C.P. 54257 Stamp of the business.