General Instructions - JANE iMatrix Manual Del Usuario

using the product and keep them for future reference.
- WARNING: This product is only suitable for use with
children that are unable to sit up unaided.
- WARNING: Only use on a firm, horizontal, flat and dry
surface.
- WARNING: Do not leave other children unattended
near the carrycot.
- WARNING: Do not use if any part is broken or dama-
ged.
- Do not place the carrycot near open fire or other sou-
rces of heat.
- The handles and base should be regularly inspected
to check for signs of wear or damage.
- Before moving or lifting the carrycot make sure that
the handle is in the correct position.
- The restraint system should be concealed when the
product is used as a carrycot.
- The child's head should never be lower than his body.
- Do not put another mattress on top of the one
supplied.
22 EN
D. GENERAL INSTRUCTIONS
In order to protect your baby adequately and to ensure their comfort
and stability in the car, the following instructions must be strictly
followed:
This seat is only suitable for cars fitted with the ISOFIX anchoring
system, approved under Regulation ECE-14 or other equivalent
standards.
Your iMATRIX safety seat can be installed in both the front seat, if it
does not have an airbag, and in the back seat of your car. Either way,
we advise you to install it in the back seat. If you position it in the front
seat of the car, this must NOT have an AIRBAG, or the airbag must be
disconnected.
Not all safety systems are exactly the same, so we advise that you
check your iMATRIX in the car in which it is going to be fitted.
It is very important not to use second-hand products, as JANÉ can only
guarantee complete safety with items used by their first buyer.
JANÉ recommends that you replace your iMATRIX safety seat with a
new one if it has been subjected to violent stresses in an accident.
Check that all the seat straps are in the correct position and duly
adjusted in your iMATRIX. Make sure that none of the straps are
twisted. Make sure the child understands he must never play with
the straps or fasteners.
E. GETTING TO KNOW THE iMATRIX SAFETY SEAT
Your iMATRIX safety seat has been designed taking into account the
latest advances in terms of safety and it has been tested under the
toughest conditions. It has the following features:
Installing in the vehicle:
iMATRIX has been approved for easy installation on the COMFY Base
from Jané with the ISO¬FIX system.
Before installing the seat with the ISOfix anchors, make sure that seat
you are going to install it on is i-size or that it is fitted with ISOfix and
that your car is on the list of compatible vehicles.
(Read the instruction manual for your vehicle, which will state which
seats are compatible with the platform.)
Comfort and safety for the baby:
3-point integrated harness.
Ventilation in the shell for greater breathability. Impact-absorbing
material over the entire surface in contact with the baby.
Adjustable headrest with 2 different positions, both of which can be
5
used on the pushchair and in the car .c:
C1 Closed position, so the baby travels in the carrycot position.
C2 Open position so the baby travels in a sitting position.
Reclining backrest with 4 positions:
R1 Position for the baby to travel lying down, highly recommendable
position for the first few months. (Not suitable for in the car)
R2-R3 Intermediate positions (Not suitable for in the car)
R4 Position for the baby to travel sitting up, and the only position suita-
ble for use of the child Restraint System in the car.
Convenience for parents:
Pro-Fix anchors compatible with JANÉ chassis (always consult the ins-
tructions for each chassis to confirm compatibility before fitting the
iMATRIX).
Carry handle, with 3 positions:
Position 1: Resting. In this position the handle lies flat against the frame.
This position is free, it does not lock.
Position 2: Carrying. This is the position used for fitting and removing
the seat from a JANÉ chassis or the COMFY Base base and for ca-
rrying.
Position 3: CAR. Anti-rollover position for use in the car.
To change the position, press both buttons 2d and turn the handle
to the required position. To move it from the resting position it is not
necessary to press the buttons, simple move the handle.
Belt height adjustment simply by pressing a button. Avoids the incon-
venience of having to remove and then fit the straps again when you
need to change the height of the belts.
Removable and washable upholstery.
EN 23