VONROC CS505AC Traducción Del Manual Original página 10

EN
• Place the cutting disk (3) on the machine spindle.
• First add the big outer washer (19), then the
small washer (20) and then the fixing bolt (21)
according to fig C. and tighten it by hand until
the spindle starts rotating.
• Press the spindle lock button (9) in order to
block the movement of the machine spindle.
• Keep pressing the spindle lock button (9). Place
the wrench (16) on the disk bolt and turn it
slightly in clockwise direction.
• When the spindle lock blocks the rotation, tigh-
ten the disk bolt by using the wrench (16).
• Loosen the spindle lock button and ensure the
spindle lock button is not blocking the spindle
anymore.
Then check if the wheel is assembled correctly:
• Turn the disk (3) by hand a few rounds to check
if it is turning freely and if it is aligned well.
• Turn the machine on and let the machine run for
at least 3 minutes.
Switching the machine on/off (Fig. B)
• To start the machine, press and hold the lock-
off button (7b) and press the on/off switch (7a).
• To stop the machine, release the on/off switch
(7a).
The workpiece clamp (5) (Fig. A, B, D)
• Place the workpiece material between front
clamp (13) and rear clamp (12).
• Raise the stopper(14) like shown in Fig. D. and
rotate the screw handle (15) forward until the
front clamp (13) touches the work piece.
• Then move the stopper (14) down (to lock the
spindle) and securely fix the workpiece by turn-
ing the screw handle (15).
Cutting at angles (Fig. E)
The machine permits cutting at angles from 0° to
45° by adjusting the rear clamp (12).
• Loosen the 2 M10 hexagon socket head bolts
(22 & 23) which hold the rear clamp (12) until
the vice can move.
• Then set the rear clamp (12). to the correct
angle and tighten both bolts (22 & 23) again.
10
Moving the rear vice (to cut bigger work pieces)
(Fig. F)
The vice permits a maximum workpiece size of
160mm when shipped from the factory. The vice can
be adjusted in to the rear to permit workpiece size
of 195 mm like shown in the right picture (fig. F).
• Loosen the 2 M10 hexagon bolts (22 & 23) on
the rear clamp (12) completely.
• Move the clamp (12) backwards and fix the bolts
(22 & 23) to the rear connection holes again.
Adjusting the depth stop (Fig. B)
The machine is equipped with a depth stop bolt,
with this bolt the maximum cutting depth can be
adjusted.
• If the depth cutting depth needs to be adjusted,
loosen the lower nut (10B), then adjust the
depth setting by turning the upper bolt (10A) to
the desired positions.
• Then fix the lower nut (10B) again.
Cutting procedure
In order to cut material always follow the following
procedure:
• Make sure the workpiece is clamped and sup-
ported well before starting the machine.
• Start the machine in upper position let it run for
a while until it reaches max. speed.
• Ensure the blade is turning freely without vibra-
tion.
• Gently move down the machine until it touches
the material.
• Keep pushing the handle with little force, make
sure the blade speed is not dropping.
• Release the on/off switch after cutting and
move the machine up gently.
• Only remove the workpiece when the cutting
disk has stopped running completely.
Don't apply excessive force on the handle
when cutting, the blade and machine will
wear out faster and it does not result in
faster cutting.
Inspecting and replacing the carbon brushes
The motor has 2 carbon brushes which will wear
out during use. It's important to check the status of
the carbon brushes, a worn-out carbon brush might
result in bad performance and motor damage.
WWW.VONROC.COM