Publicidad
Idiomas disponibles
Idiomas disponibles
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
5) SERVICE
a) Have your power tool serviced by a qualifi ed
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
HOT AIR TOOL SAFETY WARNINGS
WARNING: This tool must be placed on its
stand when not in use.
A fi re may result if the appliance is not used with
care, therefore
– be careful when using the appliance in places
where there are combustible materials;
– do not apply to the same place for a long
time;
– do not use in presence of an explosive atmos-
phere;
– be aware that heat may be conducted to com-
bustible materials that are out of sight;
– place the appliance on its stand after use and
allow it to cool down before storage;
– do not leave the appliance unattended when it
is switched on.
– This appliance can be used by children aged
from 8 years and above and persons with re-
duced physical, sensory or mental capabilities
or lack of experience and knowledge if they
have been given supervision or instruction
concerning use of the appliance in a safe way
and understand the hazards involved.
– Children shall not play with the appliance.
– Cleaning and user maintenance shall not be
made by children without supervision
TECHNICAL SPECIFICATION
Model
R1800
Feature
Voltage
Power, Watt
1800
Power switch
-
Power/Air flow
1 Mid/Mid
2 High/Full
Power/Air flow
-
LED indicator
Temperature
-
indicator screen
Residual Heat
-
Warning
FEATURES
Power switch, fi g 1A
Nozzle, fi g 1B
6
R2000
R2200-E
R2200-LCD
230-240V~ 50-60Hz
2000
2200
2200
0 OFF
1 Low/Full
2 Mid/Mid
3 High/Full
-
Yes, see features
Yes, see
-
-
features
-
Yes, see features
Handle, fi g 1C
Stand for vertical operation with free hands or stor-
age. Fig 4G
R1800 and R2000
Features as in technical specifi cation
R2200-E and R2200-LCD
Power/Air fl ow LED indicator, fi g 2D
The back 3 white LEDs show level of air fl ow
The front 3 red LEDs show level of power
R2200-LCD
Display, fi g 3E, shows the actual and target tempera-
ture (Act/Tar)
UP/DOWN buttons (/), fi g 3F
System function;
- The target temperature (Tar) can be adjusted by
pressing the UP or DOWN button (/)
R2200-E and R2200-LCD
residual heat warning
The front red LED fl ashes when the tool is turned off
indicating the nozzle is hot
WARNING!! Read all safety warnings and all
instructions.
Save all warnings and instructions for future
reference.
Ensure the power switch is in the OFF position
before plugging into the electrical outlet.
Set the power switch/temperature control to the
desired speed and temperature. Let the tool run until
it reaches operating temperature.
With the stand the tool can be used in a vertical
position with both hands free for work.
Keep hands away from the immediate nozzle area, it's
hot.
PAINT AND VARNISH REMOVAL
Never use the heat gun in combination with chemical
strippers.
WARNING! LEAD PAINT FUMES ARE VERY
HARMFUL. ALWAYS PROVIDE ADEQUATE
VENTILATION WHILE WORKING INDOORS.
Removal of paint and varnish requires some practice
but some simple working techniques are described
here. Test on a small area of paint before moving on to
larger areas.
Turn on the tool and allow it to reach working temper-
ature. Hold the nozzle 70 to 100 mm from the paint
to be removed. After a short time the paint will soften
and begin to bubble. Do not overheat the paint, as
this will cause burning and make the paint more
diffi cult to remove.
Begin scraping the paint off. Use accessory scrapers.
Scrape with smooth, even strokes, warming the sur-
face in front of the scraper by moving the tool slightly
from side to side. If paint is warmed properly, even
thick layers can be removed in a single pass. Scrape
the paint as soon as it softens since it will quickly
USAGE
Publicidad
