Descargar Imprimir esta página

Suntec Wellness KLIMATRONIC DryFix 50 perform Manual De Instrucciones página 10

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 13
Internal drying:
Please press the internal drying button (2) to activate this function. The drying process takes about one hour
and prevents the growth of mold.
During internal drying, the message "CL" is continuously shown on the display and all other modes are
turned off.
To stop the drying process, please press the button (2) again. The unit will automatically get back to the
operation with previous settings.
To stop the internal drying and switch the unit into stand-by mode, please press the On/Off button (8).
Timer:
Please press the timer button (1) to set the timer from 0 to 24 hours. It takes about 5 seconds until the mode
is set, during this time the timer key will not be available. Please set the desired mode before.
When the unit is switched on, press the timer button to set the shut-off time as described above. The timer
indicator will light up.
When the unit is switched off, press the timer key to set the switch-on time as described before. The timer
indicator will light up and the selected time will be shown on the display.
Child Lock
Please press and hold the mode button (7) for 3 seconds to switch the child lock on or off.
Sleep Mode:
Please press and hold the "Internal Drying" button (2) for 3 seconds to disable/enable sleep mode.
In sleep mode, all indication lights are turned off, the device works automatically at low wind speed and
target humidity 50%. The settings cannot be changed manually in sleep mode. Please switch on the timer
as described above, the sleep mode will be deactivated.
If the ambient humidity is high, the unit will dehumidify with the low wind speed; if the ambient humidity is
low, the compressor will stop working, only the ventilation function will be activated.
To deactivate the sleep mode, please press the mode key (7), internal drying key(2) or the on/off key(8).
Drainage
Water tank:
As soon as the water tank is full, the unit stops working, a warning signal sounds, the 'water tank full' indicator
(4) lights up on the control panel and error message "FL" will be shown on the display.
Please switch off and unplug the unit.
Please pull out the water tank carefully, open the lid of the water tank by
using the lever and empty the water.
Please clean the empty tank, close the lid and then carefully push it back
into the device.
Continuous drainage:
Please pull the plug out of the outlet.
Please remove the water tank from the appliance as described above and remove the drainage hose.
Carefully push the water tank back into the appliance without the drainage hose.
You will find the drainage opening on the back of the machine. Please unscrew the cover of the drainage
opening and remove the stopper.
Please insert the drainage hose into the opening and place the other end of the hose into a container so that
the water can drain off continuously.
Please make sure that the hose is connected tightly to prevent the water from leaking.
Please press and hold the humidity level button (6) for 3 seconds to start continuous dehumidification.
Cleaning and maintenance
To avoid injuries, please switch off and unplug the appliance before starting service or cleaning.
Cleaning:
Please unplug the unit.
Please clean the unit with a dry and soft cloth. For heavy dirt, please use a slightly damp cloth.
Please do not use any chemical products (such as petrol, alcohol, etc.). The unit's housing and the unit's
surface may be damaged.
Cleaning the dust filter:
Please carefully remove the filter from the device.
To remove dust from this filter, please use a vacuum cleaner or to tap it out carefully.
If the filter is very dirty, wash it in water with neutral detergent, rinse well with water and let it dry.
Carefully put the filter back into the unit.
Do this process about every 2 weeks to ensure optimal performance of the device.
Storage
Please use internal drying before storage to avoid moisture formation in the device.
Please disconnect the power plug of the device and bundle the power cable at the cable storage (10).
Please empty the water tank, wipe out the tank with a cloth and reinstall it.
Please clean the air filter as described above and then reinstall it in the unit.
For storage, place the unit in an upright position and avoid direct sunlight.

Publicidad

loading