Flo 79734 Manual De Instrucciones página 18

Setting the working depth (XII)
To set the working depth, use the lever, which should be moved and then introduced into the gap. The gaps are described by
numbers, which indicate the working depth: 1 – 12 mm, 2 – 8 mm, 3 – 4 mm, 4 – transport position.
Setting the excessive working depth can lead to damage to the lawn and faster wear of the rollers, as well as to damage to their
elements.
Warning! In case there is a need to change the depth during operation, always turn off the verticutter fi rst, wait for the roller to
stop, disconnect the verticutter from the power cord and then change the working depth. Accidental starting of the roller during a
depth adjustment may result in serious injury.
Connecting the verticutter to the power supply
The verticutter is only equipped with a short section of power cord with a plug, that is why it must be connected with an external
cable. Always use cords intended for outdoor use due to the nature of the machine work. The cable should have a single socket
matching the verticutter power cord plug. It is forbidden to modify the plug or socket to make them fi t. The electrical parameters
of the power cord should correspond to the electrical parameters of the device, listed on the rating plate. It should be noted
that the power cord's cross-section depends on the length of the cord. Follow the instructions below regarding the power cord
cross-section:
- 1.0 mm – cord length not greater than 40 m;
2
- 1.5 mm – cord length not greater than 60 m;
2
- 2.5 mm 2 – cord length not greater than 100 m.
When preparing for the operation and during operation, pay attention to the power cord. Protect the power cord from water, mois-
ture, oils, heat sources and sharp objects. Lay the cord so that it does not come within the reach of the roller's blades. Cutting the
cord may result in electric shock and serious injury or death. Make sure that you do not become entangled in the cord. This can
lead to a fall and serious injury.
Do not overload the power cord, and do not cause any of the cord's section to become tensioned. Do not pull the cord when
moving the device. Always disconnect the power cord plug from the socket by pulling on the plug and socket housing, never pull
on the cord.
The external power supply cable near the socket to which its plug will be connected must be passed through the eyelet of the
holder and then through the hook (XIII). Only then connect the power cord of the device to the external cable.
Make sure that the cable does not kink or become tensioned. Disconnect the cable from the plug as required, lengthen the loop
and reconnect. Only after the external cable is properly connected to the power cord, the external cable can be connected to the
mains socket.
Starting and stopping the verticutter
Place the verticutter on a fl at and level place on the lawn. Set the transport working depth position. Press and hold the power
switch lock button, then pull the power switch lever to the handlebar and hold it in this position. If the device starts, release the
pressure on the power switch lock and grasp the handlebar with both hands.
The operation will be stopped when the power switch lever is released. The roller may still rotate for a while.
Working with the verticutter
Depending on the type of work to be done, one of the two rollers should be selected and installed correctly. A roller with blades is
used to cut (scarify) the soil on which the lawn grows. The roller with springs and hooks is used to clean (verticut) the surface of the
lawn, e.g. from moss or leaves. This roller with the set working depth too deep can cause damage to the lawn. It is recommended
to use this roller for surface work with the minimum working depth set.
Before the proper operation, it is recommended to check the operation of the rollers at diff erent working depth settings in less
exposed places.
Before starting work, prepare the lawn. Check that there are no obstacles on the lawn that could be caught by the blades and
damage the verticutter, or be ejected and pose a risk to an operator or bystanders.
The soil on which the lawn grows should not be too hard. Too hard soil will lead to faster wear of the elements that go into the
ground during operation, and can also lead to a decrease in the performance of the machine and its overheating.
Check that there are no electrical cables in the work area that could be cut by the blade. Damage to an electrical cable presents
a risk of electric shock, which can lead to serious injury or death.
Make sure that there are no bystanders or pets in the work area. If such persons appear during operation, stop the machine
immediately and only then warn people of the danger.
Check all machine components before starting work. In case the damage is detected, do not start work before removing the
damage or replacing the damaged components with new ones. Make sure that the ventilation openings are clear. If necessary,
clean them with a soft cleaning tool or brush. Do not use sharp or metal objects for cleaning the product ventilation openings.
Check the tightness of the screw connections. Tighten if necessary.
Check that the handlebars are clean, free of grease and other contamination. If necessary, clean them with a soft cloth.
O R I G I N A L
18
EN
I N S T R U C T I O N S