Chicco Next 2 me Essential Manual De Instrucciones página 15

the swivel feet "A1" and "A2", insert the tubes of the central sup-
port structure "B" in their supports "A8" pushing the pins "B2" until
a locking CLICK is heard (Fig. 3). Complete one side first then the
other.
3. Being careful to position the openable side of the structure on
the same side as the swivel feet "A1" and "A2", insert the fastening
support "C1" into the upper section of the leg supports "A" until
you hear the pin locking CLICK "A7" (Fig. 4).
4. Open zippers "E1", "E2" and "E3" on the fabric. Dress the product
having the fabric run along the slots "E5" on the open side of ei-
ther end of the upper tube (Fig. 5).
5. Fasten the removable tube "C2" by pressing down so that it locks
into the slots "C4" (Fig. 6).
6. Position the folding barrier fabric on the detachable tube "C2"
(Fig. 7) and use the zipper "E3" to close (Fig. 8). Close the vertical
zippers "E2" (Fig. 9).
7. Complete the operation by wrapping the fabric around the rear
section of the upper tubing (Fig. 10) and close the zipper "E1" (Fig.
11).
8. Fasten the two straps with snap buttons "E4" to the central sup-
port structure "B" (Fig. 12).
9. Complete the operation by putting the mattress in place.
10. Lock the 2 wheels of the crib by lowering the levers that activate
the brakes (Fig. 13).
The crib is now ready to be used.
WARNING: Make sure that all the fasteners are engaged correctly
and that the zippers are closed and locked at the end.
WARNING: Do not use the crib with the articulated feet partially or
completely turned or released (Fig. 14). The position of correct use
is illustrated in Fig. 15. In the case of accidental knocking against
the articulated feet, put them back in the correct position by lifting
the crib slightly.
ADJUSTING THE CRIB HEIGHT
The height of the crib can be adjusted in 6 different positions. To
adjust the height press up on the adjustment buttons "A4" and raise
or lower the crib until the desired position is reached (Fig. 16).
The base of the crib can be slightly inclined by adjusting the 2 leg
supports to different heights (Fig. 17).
WARNING: The crib can be inclined by a maximum of 2 positions
between one leg support and the other (e.g., right leg in position 3
and left leg in position 1, see Fig. 18).
WARNING: The child's head must always be positioned near the
raised end (Fig. 19).
SIDE SLEEPING CONFIGURATION (FASTENING THE CRIB TO
THE BED)
The crib can be fastened to the parents' bed (side sleeping config-
uration).
WARNING - IMPORTANT FOR YOUR CHILD'S SAFETY.
This configuration is allowed only with beds that permit compliance
with all the conditions described in this paragraph.
Specifically, the lowered side of the crib must always be positioned
against the mattress of the parents' bed and the parents' mattress
must be carefully aligned with the height of the crib's side (Fig. 20).
Moreover, the crib must be firmly fastened to the structure of the
parents' bed or to the mattress support (mesh or slat sprung base).
WARNING: Check that the structure of the crib in side sleeping
configuration does not interfere with the parents' bed.
WARNING: During use, make sure that the bedsheets, blankets, etc.
do not interfere with the crib's space.
11. Open the ends of the foldable side by opening the vertical zip-
pers "E2" completely and opening the horizontal zipper "E3".
12. Let the fabric fall outside the crib (Fig. 21).
13. Remove the tube "C2" by sliding the tab "C3" and pulling up on
the tube (Fig. 22). Complete one side first then the other.
WARNING: keep the detached tube out of reach of children.
WARNING: only use the crib with the fabric lowered when in
co-sleeping configuration.
1415. Put the crib against the parents' bed and check the height of
the crib compared to the parents' mattress.
WARNING: the top of the parents' mattress must always be higher
than the side of the crib (Fig. 23A - 23B).
WARNING: In side sleeping configuration, the 2 leg supports of the
crib must be set at the same height
14. To fasten the crib to the parents' bed (co-sleeping configuration),
use the pair of supplied straps "D".
16. Fasten the grey prongs "D2" to the grey buckles "B1" under the
fabric cover on either side. Make sure that the red buckles "D1"
are positioned above the belt strap (Fig. 24).
17. Then run the strap around the structure of the parents' bed from
the bottom up (Fig. 25) and fasten the red buckle "D3" to the red
prong "D1" forming a noose (Fig. 26). Repeat this operation on
the other side as well. To make installation easy, when fastening
the buckles, always keep the crib slightly away from the parents'
bed.
18. Put the crib up against the parents' bed and tighten the loop by
pulling firmly on the straps (Fig. 27). Carry out this step first on
one side and then on the other, adjusting the straps until the
crib is in firm contact with the parents' mattress.
WARNING: Before use, always make sure that there is no space be-
tween the parents' mattress and crib's side. Otherwise, adjust the
straps by pulling firmly until complete contact is restored.
19. Lock the crib wheels as described in point 10.
When fastening the crib to the bed, if the feet of the crib cannot be
inserted under the parents' bed, the bed can be fastened anyway by
the following the instructions above with the added step of rotating
the swivel feet when putting the crib up against the bed.
To rotate the feet press the release button "A6" and use one hand to
rotate the feet of the crib inward (Fig. 28).
WARNING: Use the product with beds and/or mattresses with
straight sides only. Do not use the product with round beds and/or
mattresses or water mattresses.
WARNING: When the product is used in "Co-sleeping configuration
(fastened to the bed), " it must always be mounted on the long side
of the bed. DO NOT install the product at the head or foot of the
bed.
USE IN CRIB CONFIGURATION
20. To use the product in this configuration, reposition the detacha-
ble tube "C2" by sliding the ends of the fastening slots "C4" until
a locking CLICK is heard.
21. Close the horizontal zipper "E3" and the two vertical zippers "E2".
22. If you wish to move the crib, release the brakes by raising the
lever (Fig. 29).
CARE AND MAINTENANCE
The crib and mattress have a resistant fabric lining that can be re-
moved completely and washed.
The steps for removing the fabric cover and putting it back on the
product must only be carried out by an adult. Regularly inspect the
product for signs of wear and damage. In the case of damage, do
not use and keep out of reach of children.
When washing the fabrics pay close attention to the instructions
on the label.
Do not use solvents, abrasive or overly aggressive products.
Wash by hand in cold water
30° C
Do not use bleach
Do not tumble dry
Do not iron
Do not dry clean
Check that the fabric and the stitching are in good condition after
each wash.
WARNING: When covering or removing the cover, take care when
handling the fabric parts to avoid accidental tears or damage.
15