Publicidad
Safety instructions
For your protection
• Read the operating instructions completely before star-
ting up and follow the safety instructions.
• Keep the operating instructions in a place where it can be ac-
cessed by everyone.
• Ensure that only trained staff work with the device.
• Follow the safety instructions, guidelines, occupational health
and safety and accident prevention regulations.
• Electrical outlet must be grounded (protective ground contact).
Attention – Magnetism!
ATTENTION
Effects of the magnetic field have to be ta-
ken into account (e.g. data storage media,
cardiac pacemakers ... ).
RT
DANGER
Risk of burns!
Exercise caution when touching parts of
the housing and the heating plate.
The heating plate can reach dangerous temperatures. Pay atten-
tion to the residual heat on the heating plate after switching off
the stirrer.
RT
WARNING
Ensure that the power cord set / tempera-
ture sensor cable does not touch the hea-
ting plate.
• Wear your personal protective equipment in accordance with the
hazard category of the media to be processed. There may be a
risk from:
- splashing and evaporation of liquids,
- ejection of parts,
- release of toxic or combustible gases.
• Set up the appliance in a spacious area on an even, stable, clean,
non-slip, dry and fireproof surface.
• The feet of the device must be clean and undamaged.
• Check the device and accessories for damage before each use.
Do not use damaged components.
• Gradually increase the speed.
• Reduce the speed if
- medium splashes out of vessel because the speed is too high,
- device is not running smoothly,
- container moves on the base plate.
RT
WARNING
Caution! In unsupervised and safe opera-
tion, this device may only handle or heat
media whose flash point is above 180 °C.
The temperature limit must always be set to at least 25 °C lower
than the flash point of the media used. (acc. to EN 61010-2-010)
Beware of hazards due to:
WARNING
- flammable materials,
- combustible media with a low boiling temperature,
- glass breakage,
- incorrect container size,
- overfilling of media,
- unsafe condition of container.
• The appliance may heat up when in use.
• The base plate can heat up due to the action of the drive mag-
nets at high motor speeds, even if the heater is not operational.
• Process pathogenic materials only in closed vessels under a sui-
table extractor hood. Please contact IKA if you have any questi-
ons.
10
Do not use the device in explosive atmos-
DANGER
pheres, it is not EX-protected.
With substances capable of forming an
explosive mixture, appropriate safety measures must be applied,
e.g. working under a fume hood.
To avoid body injury and property damage, observe the relevant
safety and accident prevention measures when processing haz-
ardous materials.
Only process media that will not react
DANGER
dangerously to the extra energy produced
through processing. This also applies to
any extra energy produced in other ways,
e.g. through light irradiation.
• Please observe the operating instructions for any accessories.
• Safe operation is guaranteed only with the use of original IKA
accessories.
• Accessories must be securely attached to the device and cannot
come off by themselves. The centre of gravity of the assembly
must lie within the surface on which it is set up.
• Always disconnect the plug before fitting accessories.
• The appliance can only be disconnected from the mains supply
by pulling out the mains plug or the connector plug.
• The socket for the mains cord must be easily accessible.
• It may be possible for wear debris from rotating accessory parts
to reach the material being processed.
• When using PTFE-coated magnetic bars, the following has to be
noted:
Chemical reactions of PTFE occur in contact with molten or so-
lute alkali metals and alkaline earth metals, as well as with fine
powders of metals in groups 2 and 3 of the periodic system at
temperatures above 300 °C - 400 °C. Only elementary fluorine,
chlorotrifluoride and alkalimetals attack it; halogenated hydro-
carbons have a reversible swelling effect.
(Source: Römpps Chemie-Lexikon and „Ullmann" Volume 19)
For protection of the equipment
• The appliance may only be opened by experts.
• The voltage stated on the type plate must correspond to the
mains voltage.
• Do not cover the device, even partially e.g. with metallic plates
or film. This results in overheating.
• Protect the appliance and accessories from bumps and impacts.
• Ensure that the base plate is kept clean.
• Observe the minimum distances between the devices, between
device and wall and minimum distances (min. 800 mm) above
the assembly, see Fig. 2.
>100 mm
>100 mm
Fig. 2
Unpacking
• Unpacking
- Please unpack the device carefully
- In the case of any damage a detailed report
must be sent immediately (post, rail or forwarder)
Correct use
• Use
- For mixing and / or heating liquids
• Range of use
Indoor environments similar to that a laboratory of research,
teaching, trade or industry area.
Commissioning
RO/RT
Observe the ambient conditions (temperature, humidity, etc.)
listed under Technical Data.
The device is switched on and off via the switch (A) located on
the right-hand side of the device. On the front panel a small
arrow labelled Power above the display (B) indicates the location
of the switch.
Temperature limit
RT
The max. achievable hotplate temperature is limited to 150 °C
due to the design. Once this limit has been attained, the device
switches off the heating.
Setting the temperature limit
RT
The temperature limit is set as follows:
Switch the device on using the On/Off switch
on the right side of the device.
As soon as the display shows SAFE, press and
hold down the Temp membrane key and use
Stirring function
RO/RT
The stirring function is started and stopped by pressing the „Start/
Stop" button (C).
Pressing the +/- buttons (E or D) increases or reduces the speed.
• Delivery scope
RO
RT
- Magnetic stirrer
- Heating magnetic-
RO 5/10 or 15
stirrer RT 5/10 or 15
- power supply unit
- mains cable
- operating instruction
- operating instruction
The safety of the user cannot be guaranteed:
- if the device is operated with accessories that are not supplied
or recommended by the manufacturer,
- if the device is operated improperly or contrary to the
manufacture's specifications,
- if the device or the printed circuit board are modified by third
parties.
After the device is switched on a display self-test is performed.
The display cycles through the following information:
• All segments light up
• The software version and the selected mode are displayed
• The selected "Eco Mode" is displayed
(E when ECO mode is active)
• If the drive has not been started the display reads „OFF". If
the drive has been started the selected speed is displayed.
The temperature limit must all-
WARNING
ways be set at least 25 °C lower than
the flash point of the media to be
processed!
the +/- membrane keys (H or I) to set the
desired temperature limit.
The set temperature limit is displayed.
Once the Temp membrane key is released, the temperature limit
is saved.
11
Publicidad
