VONROC IW502DC Traducción Del Manual Original página 6

EN
resulting in fire, explosion or risk of injury.
f) Do not expose a battery pack or tool to fire
or excessive temperature. Exposure to fire or
temperature above 130 °C may cause explosion.
NOTE The temperature „130 °C" can be replaced
by the temperature „265 °F".
g) Follow all charging instructions and do not
charge the battery pack or tool outside the
temperature range specified in the instructions.
Charging improperly or at temperatures outside
the specified range may damage the battery and
increase the risk of fire.
6) Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the
power tool is maintained.
b) Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
c) If the supply cord of the charger is damaged, it
must be replaced by the manufacturer, its ser­
vice agent or similarly qualified persons in order
to avoid a hazard.
ADDITIONAL SAFETY WARNINGS FOR IM-
PACT WRENCHES
1. Hold the power tool by insulated gripping surfa­
ces, when performing an operation where the
fastener may contact hidden wiring. Fasteners
contacting a "live" wire may make exposed
metal parts of the power tool "live" and could
give the operator an electric shock.
2. Wear ear protectors when impact drilling.
Exposure to noise can cause hearing loss.
3. Check the impact socket carefully for wear,
cracks or damage before installation.
4. Hold the tool firmly.
5. Brace the tool properly before use. This tool
produces a high output torque and without
properly bracing the tool during operation, loss
of control may occur resulting in personal injury.
6. Keep hands away from rotating parts.
7. Do not touch the impact socket, bolt, nut or the
workpiece immediately after operation. They
may be extremely hot and could burn your skin.
8. Always wait until the power tool has come to
a complete stop before placing it down. The
application toolcan jam and cause you to lose
control of the power tool.
6
9. Always be sure you have a firm footing. Be sure
no one is below when using the tool in high
locations.
10. The proper fastening torque may differ depen­
ding upon the kind or size of the bolt. Check the
torque with a torque wrench.
11 Make sure there are no electrical cables, water
pipes, gas pipes etc. that could cause a hazard
if damaged by use of the tool. Use suitable de-
tectors to determine if there are hid-den supply
lines or contact the local utility companyfor
assistance.
SAFETY WARNINGS FOR BATTERY
a) Do not open the battery. Danger of short-
circuiting.
b) Protect the battery against heat, e. g., against
continuous intense sunlight, fire, water, and
moisture. Danger of explosion.
c) In case of damage and improper use of the bat­
tery, vapours may be emitted. Ventilate the area
and seek medical help in case of complaints.
The vapours can irritate the respiratory system.
d) Use the battery only in conjunction with your
Vonroc product. This measure alone protects
the battery against dangerous overload.
e) The battery can be damaged by pointed objects
such as nails or screwdrivers or by force
applied externally. An internal short circuit can
occur and the battery can burn, smoke, explode
or overheat.
SAFETY WARNINGS FOR CHARGER
Intended use
Charge only CD801AA and CD803AA type rechargea-
ble Battery packs with the charger. Other types of bat-
teries may burst causing personal injury and damage.
a) The appliance is not to be used by persons
(including children) with reduced physical,
sensory or mental capabilities, or lack of expe­
rience and knowledge, unless they have been
given supervision or instruction.
b) Children being supervised not to play with the
appliance.
c) Do not recharging non­rechargeable batteries!
d) During charging, batteries must be placed in
the well ventilated area!
WWW.VONROC.COM