EGO PS1000E Manual De Instrucciones página 10

NOTICE:
The pole saw is not filled with oil at the time
EN
of purchase. It is essential to fill the tank with chain
oil before use. Operating the pole saw without chain
oil or when the oil level is below a certain amount will
result in damage to the pole saw. Chain life and cutting
capacity depend on optimum lubrication. The chain is
automatically lubricated with chain oil during operation, if
there is sufficient oil in the reservoir. Oil level should also
be checked after every 20 minutes of use and refilled as
needed.
1. Remove the battery pack from the power head.
2. Clean the oil-tank cap and the area around it to
ensure that no dirt falls into the oil tank.
3. Lay the pole saw on a firm, flat surface, so that the
oil tank cap is facing upwards, then remove the cap
(Fig. J).
4. Carefully pour the bar and chain oil into the tank until
it fills to the tank neck. Be careful not to let the oil
spill from the opening. Wipe off any excess oil.
NOTICE:
◾
Never use oil or other lubricants not specifically
designed for use on the bar and chain. This can lead
to a clogged oil system, which may cause premature
wear of the bar and chain.
◾
Check the oil level frequently and refill as needed.
◾
Do not use dirty, used or other contaminated oil.
Damage may occur to the bar or chain.
◾
It is normal for oil to seep from the saw when it is not
in use. To prevent seepage, empty the oil tank after
each use, and then run the saw for one minute. When
storing the tool for a long period of time, be sure the
chain is lightly lubricated; this will prevent rust on the
chain and bar sprocket.
◾
To preserve natural resources, please recycle or
dispose of oil properly. Consult your local waste
authority for information regarding available recycling
and disposal options.
ADJUSTING THE TELESCOPIC POLE (Fig. K)
1. Lift the quick release lever to unlock the telescopic
pole.
2. Extend the telescopic pole to the required length.
3. Press the quick release lever down to lock the
telescopic pole securely.
ASSEMBLING THE SHOULDER STRAP
Depress the strap hook to open it and attach it onto
shoulder strap hanger on the saw (Fig. L). Adjust the
shoulder strap to a comfortable operating position.
10
56 VOLT LITHIUM-ION CORDLESS POLE SAW— PS1000E
WARNING:
When emergency occurs, take the strap
off from your shoulder immediately to avoid injury.
INSTALLING/REMOVING THE BATTERY PACK
NOTE:
Fully charge the battery pack before first use.
Use only with battery packs and chargers listed in fig. A2.
To Attach
Align the battery ribs with the mounting slots and press
the battery pack down until you hear a "click" (Fig. M).
WARNING:
Make sure the battery pack is locked in
place before operation. Failure to securely seat the battery
pack could cause the battery pack to fall out, resulting in
serious personal injury.
WARNING:
Always be aware of the location of your
feet and children or pets around you when pressing the
battery-release button. Serious injury could result if the
battery pack falls. NEVER remove the battery pack at a
high location.
To Detach
Depress the battery-release button and pull the battery
pack out (Fig. N).
LED WORK LIGHT (Fig. O)
The LED work light is at the front of the pole saw
attachment, in line with the saw chain. This feature
provides extra light for users to see where the saw chain
is when cutting branches high up in the tree.
The work light will automatically turn on when squeezing
the trigger switch and it will be off about 10 secs after
releasing the trigger switch.
STARTING/STOPPING THE TOOL
Before Starting the Pole Saw
WARNING:
NEVER OPARATE THE POWER HEAD
WITHOUT AN ATTACHMENT. Do not attempt to start the
power head before connecting the pole saw attachment.
NOTICE:
Before starting the pole saw, check for the quick
chain-tension adjustment, oil level and chain and teeth
sharpness. As well as, gripping method, balanced footing
and proper distance away from the ground are needed
(Fig. Q).
To Start (Fig. P)
1. Install the battery pack.
2. Make sure that no objects or obstructions that could
come in contact with the bar and chain are in the
immediate vicinity.