Publicidad
Idiomas disponibles
Idiomas disponibles
Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or
fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can cause
you to lose control.
Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets
will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges
and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase
the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces the risk of electric shock.
WARNING: When used in Australia or New Zealand, it is recommended that this tool is ALWAYS
supplied via Residual Current Device (RCD) with a rated residual current of 30mA or less.
Personal safety
a) Stay alert, watch what you are doing and use common sense when operating a power
tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol
or medication. A moment of inattention while operating power tools may result in serious
personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective equipment
such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to
power source and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or energising power tools that have the switch
on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables better control of
the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection facilities,
ensure these are connected and properly used. Use of dust collection can reduce dust-related
hazards.
Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application. The correct
power tool will do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power tool that
cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the battery pack from the power tool
before making any adjustments, changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons unfamiliar
with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of
parts and any other condition that may affect the power tool's operation. If damaged,
have the power tool repaired before use. Many accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with these instructions,
taking into account the working conditions and the work to be performed. Use of the power
tool for operations different from those intended could result in a hazardous situation.
Service
a) Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained.
850W SDS Plus Hammer Drill
Additional Safety for SDS Plus Drills
WARNING: If you suspect or discover asbestos is present in any area you are working seek
professional advice immediately. Removal of asbestos should be done by a licensed contractor.
Contact the HSE in the UK (www.hse.gov.uk) or your national health and safety authority in your
country for further information about dealing with asbestos. European Directive 2009/148/EC
provides additional information related to exposure to asbestos at work.
• It is imperative to follow all national safety regulations concerning the type of work being
undertaken.
• Do not allow anyone under the age of 18 years to use this tool, and ensure that operators are
qualified and familiar with the operating and safety instructions
• Masonry drilling or chiselling can create sharp particles that will impact the operator. Wear
impact-resistant safety glasses and protective clothing, including safety boots
• Core drills should only be used with SDS drills featuring a safety clutch to prevent jamming,
which could cause an injury to the operator
• If the safety clutch operates during use, quickly release the trigger and remove the core drill or
bit from the masonry surface being drilled. Do not continue work until the cause of the safety
clutch operating is understood
• Do not operate SDS drills whilst up a ladder or in any location where there is a risk of falling. SDS
drills are heavy and produce strong vibration and high torque in use
• Wear suitable protective anti-vibration gloves that are non-fabric or coated fabric to prevent loose
strands of material catching in the rotating drill bit. Discard gloves immediately if material is
visibly frayed
• Drilling can produce large volumes of dust and debris that may be toxic. Wear respiratory
protection suitable for the work being undertaken. A minimum rating of FFP2 is recommended
• SDS drills produce high volumes of noise and suitable ear protection must be worn at all times
while operating the tool
• SDS drills produce a very high level of vibration when operating in hammer or chisel mode.
Frequent breaks are advised
• Only use SDS Plus chisels or points with SDS drills that can disengage rotary drilling mode
• Use metal and voltage detectors to locate concealed electric, water or gas lines. Avoid touching
live components or conductors
• Extension cable reels used with this tool must be completely unwound. Minimum conductor
cross section: 1.25mm2
• Extension reels used outside should be designed for outdoor use and should feature water-
protected sockets and correct cable insulation
• When using an SDS drill outdoors, an RCD device must be used either by connecting to a socket
which incorporates an RCD, or through use of an inline RCD
• Ensure that the chisel or drill bit is securely fixed in the chuck before operating the tool. Insecure
drill bits can be ejected from the machine, causing a hazard
• Ensure lighting is adequate
• Use both hands when operating this tool
• Always use the auxiliary handle supplied with the tool
• Do not place pressure on the tool - to do so could shorten its service life
• Drill bits become hot during operation. Allow to cool prior to handling
• If you are interrupted when operating the drill, complete the process and switch off before
diverting your attention elsewhere
• Always disconnect the SDS drill from the electric supply before changing a chisel or drill bit
• Examine the chuck regularly for signs of wear or damage. Have damaged parts repaired by a
qualified service centre
• Always wait until the drill has come to a complete stop before placing it down
• On completion of the work, disconnect the tool from the power source and remove the chisel/bit
from the machine
• Periodically check all nuts, bolts and other fixings and tighten where necessary
• Visibly check the tool after use, especially the power cable, which can be damaged by sharp
masonry
• Always fit the dust guard to the bit in use to prevent damage from debris entering the SDS chuck
• If operating the tool causes discomfort in any way, stop immediately and review your method of
use
silverlinetools.com
7
Publicidad
