Descargar Imprimir esta página

Whittier Wood Products Palmer 586Wb Instrucciones Para Armar

Cómoda con seis cajones

Publicidad

Enlaces rápidos

Model #
586Wb
Palmer 6-Drawer
Dresser
Assembly Instructions
Congratulations!
This fine piece of furniture will make a handsome
addition to your home. For the best results, start by
reading both the Assembly Instructions and
Finishing Hints before you begin your project.
For normal household use only.
recommended for commercial use.
Do not climb, sit or stand on this piece of
furniture.
Unload items from this unit prior to moving.
Do not overload the drawers on this unit.
For maximum stability, attach unit to the wall using
the enclosed hardware as per instructions.
P.O. Box 2827
Eugene, OR 97402 USA
Service Policy:
which are defective, missing or damaged
during assembly. Please contact Whittier
Wood Products customer service department
directly (by phone, fax, mail or email) for
replacement parts.
Hours:
Our friendly customer service staff
can be reached Monday-Friday 7:00 a.m. to
5:00 p.m. (Pacific Time). A message can be
left 24 hours a day, 7 days a week.
To Order:
Provide the complete furniture
model number (upper left corner of this
page), part letter, production code, quantity
needed, reason for replacement and your full
name and address along with a telephone
number in case we need to contact you.
Parts ship from our Eugene, Oregon factory
within 1 or 2 business days from the time
we receive the request. Please allow 5-10
business days for delivery.
Outside U.S. or Canada: 541-687-0213
Fax: 541-687-2060 • www.whittierwood.com
Mail: P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.
Read both the Assembly Instructions and Finishing
Hints completely before beginning.
Store the parts: 1) in their box; 2) in a dry place; 3) in
temperatures ranging from 40° to 90°. (Not on a cold,
possibly damp, cement floor.)
Inspect your furniture periodically for any loose glue
joints or screws, or any other problem which may
be affecting the stability of your furniture. Tighten or
repair as needed.
Production Code:
We will replace any parts
Rev. 6/07

Publicidad

loading

Resumen de contenidos para Whittier Wood Products Palmer 586Wb

  • Página 1 Model # 586Wb Palmer 6-Drawer Dresser Service Policy: We will replace any parts which are defective, missing or damaged Assembly Instructions during assembly. Please contact Whittier Wood Products customer service department directly (by phone, fax, mail or email) for replacement parts. Hours: Our friendly customer service staff can be reached Monday-Friday 7:00 a.m.
  • Página 2 586Wb Palmer 6-Drawer Dresser — Parts List BEFORE BEGINNING ASSEMBLY: Check that the quantities of the parts received match those on the parts list below. EDGE BAND BANDE DE BORD BORDE A — Drawer End — Qty. 6 B — Drawer Side — Qty. 12 Gb —...
  • Página 3 586Wb Palmer 6-Drawer Dresser — Parts List (cont.) M — Cam Connector X — Front Vertical Support — Qty. 1 — Qty. 4 S — #8 x 7/8" LoProfi le Screw — Qty. 24 Y — Back Vertical Support — Qty. 1 N —...
  • Página 4 IMPORTANT: We recommend fi nishing the unit before fi nal assembly. Before fi nishing, read enclosed fi nishing hints. NOTE: Due to the fact that more than one type of hardwood is used, we recommend testing for desired color. To test for desired color on: a) Veneer parts—apply stain to unexposed portion of side panel.
  • Página 5 FIG. 2 2) Attach three Drawer Slides (Cabinet Side Left) (V2) to the front Vertical Support (X) and the Back Vertical Support (Y) with #6 x 5/8" Undercut (type 17) Screws (R) into the pre-punched holes in the supports. The notches in the vertical supports must be toward the bottom and face away from each other.
  • Página 6 FIG. 4 4) Glue Dowels (U) for sleepers into Left and Right Sides (Gb&Hb). Glue the Left Side (Gb) to the sleeper assembly. Insert the dowels in the sides into the holes in the sleepers. Fasten in place with #8 x 1¾" Pan Head Screws (O) through the holes in the notches. See FIGURE 4.
  • Página 7 FIG. 6 STAIN TEST AREA 6) With the unit lying face down, measure from top left to bottom right and from top right to bottom left. If the unit is square, the measurements will be equal. If one is longer, tap the bottom of the side panel on the longer side until equal.
  • Página 8 FIG. 8 FIG. 9 8) Attach Drawer Slides (Drawer Side Left) (V4) and (Drawer Side Right) (V3) to the drawers. The wheels should be to the rear and the front edge should be fl ush with drawer side. Attach the slides with three #6 x 5/8"...
  • Página 9 Modelo # 586Wb Cómoda con seis cajones Palmer Normas para obtener servicio: Reemplaza- remos las piezas que tengan defectos, falten o se Instrucciones para Armar dañen durante el armado. Sírvase comunicarse con el departamento de servicio al cliente de Whittier Wood Products directamente (por teléfono, fax, correo o e-mail) para obtener piezas de repuesto.
  • Página 10 586Wb Cómoda con seis cajones Palmer LISTA DE PIEZAS Antes de comenzar el montaje, verifi que que el total de piezas recibidas concuerde con la cantidad indicada en la lista que fi gura a continuación. Cantidad Cantidad Cantidad Panel posterior del cajón ..6 Tornillo negro #8x1¼"...
  • Página 11 586Wb – INSTRUCCIONES PARA ENSAMBLADO posterior (Y) valiéndose de tornillos rebajado de latón #6x5/8" del panel lateral del lado más largo hasta que sean iguales. (R) para fi jarlos en los orifi cios prefabricados ubicados en Coloque los paneles posteriores (L) en el mueble de modo que las dos piezas se unan en el larguero del medio y puedan los soportes.
  • Página 12 No. de modèle 586Wb Dressoir Palmer à six Politique de service : Nous remplacerons toutes tiroirs les pièces défectueuses, manquantes ou endom- magées pendant le montage. Veuillez contacter Instructions de Montage directement le service clientèle de Whittier Wood Products (par téléphone, fax, courrier ou e-mail) pour obtenir les pièces de remplacement.
  • Página 13 586Wb Dressoir Palmer à six tiroirs Nomenclature des pièces AVANT DE COMMENCER L’ASSEMBLAGE, vérifi ez si la quantité des pièces reçues correspond à la liste ci-dessous. Qté Qté Qté Extrémité du tiroir ..6 Vis noire nº...
  • Página 14 586Wb – INSTRUCTIONS DE MONTAGE égaux. Placez les arrières (L) sur l’unité de manière à ce Introduisez un connecteur de came (M) dans chacun des que les deux pièces se rencontrent sur la traverse du milieu quatre trous situés au fond du dessus (J). Voir la FIGURE et puissent être fi...