Publicidad
Idiomas disponibles
Idiomas disponibles
CONTROLS
7
Control (Function)
Setting
Flashing
Amplifier Powering Up, Audio Output Muted
Green
Green
On-Normal Operation, Active Audio Output
On-Safe Mode, Over-Temperature Condition, Audio Output Reduced
Red
Status LED
• Reverts to normal operation when temperature returns to a safe level
6
(indicates operating
On-Safe Mode, Over-Current Condition, Audio Output Muted
status)
Amber
• May exhibit repetitive, audible ticking or thumping noise in the output
(yellow)
• Inspect for speaker/wire short circuit or low impedance
Amplifier Turns Off (unexpectedly), Low-Voltage Condition
LEDs Off
• Occurs when battery or remote turn-on voltage drops below 10V
• Reverts to normal operation when voltage rises above 11V
+12V Remote Turn-On (Preferred)
Remote
• Controlled by a switched +12V circuit or turn-on
output of your source unit/OEM interface
DC Offset-Sensing (Automatic)
Turn On Mode
• Turns On by detecting the presence of small DC
Offset
signal in OEM audio outputs and turns Off after
(configures
the signal is removed
activation method)
Signal-Sensing (Automatic)
• Turns On by detecting full-range OEM audio
Signal
signals and turns OFF after the signal is removed
(within 30 seconds)
Input Filter
Car
Select for most installations (automotive or marine)
(configures input
filter application)
Boat
Select if experiencing interference from high-current mechanical switches/devices
7
Select when using CH. 1&2 inputs only
• CH. 3 will operate with CH. 1 signal
2 Ch.
• CH. 4 will operate with CH. 2 signal
• SUB CH. signal will be the sum of CH. 1&2 signals
Input Mode
Select when using CH. 1&2 and CH. 3&4 inputs
(configures input
4 Ch.
• SUB CH. signal will be the sum (non-fading) of all four input signals
signal connections)
Select when using all six inputs
• SUB CH. inputs accept stereo or mono signals
6 Ch.
• If only one subwoofer channel signal is available, a Y-adaptor is recommended to feed
both SUB CH. inputs.
Remote Level Mode
All
Adjusts level of all channels equally
(configures HD-RLC
operation - optional)
Sub Ch.
Adjusts level of subwoofer channel only
6 | JL Audio® - XDM1000/5
6
Description
• Designed for high-level
(speaker) signals only
• Detects input signal from
CH. 1 (L) only
• Using DC Offset or Signal
Sensing methods will turn the
"Remote" terminal into a +12V
turn-on output.
• Multiple amplifiers can be controlled
from a single HD-RLC using a non-
duplex phone line splitter and multiple
phone cables.
CONTROLS
Control (Function)
Setting
Input Sens.
Use to match the source unit's output voltage with the inputs of each pair of
(adjusts each channel
Variable
amplifier channels. See Appendix A for detailed information.
pair's input stage)
Off
Filter defeated; passes full range of frequencies present at the inputs
HP Filter Mode
(configures the
x1
Attentuates frequencies below the CH. 1&2 "Filter Freq. (Hz)" dial, at a rate of 12dB/octave
high-pass filter
Attentuates frequencies ten times higher than below the CH. 1&2 "Filter Freq. (Hz)"
of CH. 1&2)
x10
dial, at a rate of 12dB/octave
Filter Freq. (Hz)
Use with the "HP Filter Mode" switch to adjust the cutoff frequency of channel 1&2's
(adjusts the high-
high-pass active filter:
Variable
pass filter cutoff
x1 = 50 Hz – 500 Hz / 12dB per octave
frequency)
x10 = 500 Hz – 5,000 Hz / 12dB per octave
Off
Filter defeated; passes full range of frequencies present at the inputs
Filter Mode
Attentuates frequencies below the CH. 3&4 "HP Filter
(configures the
BP
Freq. (Hz)" dial AND above the CH. 1&2 "Filter Freq. (Hz)"
high-pass or band-
8
setting, at a rate of 12dB/octave
pass filter
of CH. 3&4)
Attentuates frequencies below the CH. 3&4 "HP Filter Freq. (Hz)" dial,
HP
at a rate of 12dB/octave
HP Filter Freq. (Hz)
(adjusts the high-
Use to adjust the cutoff frequency of channel 3&4's high-pass active filter,
Variable
pass filter cutoff
from 50 Hz – 500 Hz / 12dB per octave
frequency)
Off
Filter defeated; passes full range of frequencies present at the inputs
LP Filter Mode/Slope
Attentuates frequencies above the SUB CH. "LP Filter Freq. (Hz)" dial,
(configures the
12dB
at a rate of 12dB/octave
low-pass filter and
slope of SUB CH.)
Attentuates frequencies above the SUB CH. "LP Filter Freq. (Hz)" dial,
24dB
at a rate of 24dB/octave
LP Filter Freq. (Hz)
(adjusts the low-
Use to adjust the cutoff frequency of the subwoofer channel's low-pass active filter,
Variable
pass filter cutoff
from 50 Hz – 500 Hz / 12dB per octave
frequency)
8
Description
" Input Mode" switch
must be set to 2 Ch.
7
Publicidad
