Publicidad
Idiomas disponibles
Idiomas disponibles
Use
Linking the Device to Smartmi Link
Intelligent Control with Apple HomeKit
This product has been linked to the
1
Open the Home app on your iPhone/iPad.
Smartmi Link and can be controlled
using the app.
2
Tap "Add Accessory" and then scan the HomeKit setup code on the
Scan the QR code or search for
product sticker (two stickers on the device unit, see illustration), or enter
"Smartmi Link" on the app store to
the eight-digit setup code above the HomeKit Setup Code. The device
download and install the app. Go to
will then be linked to the Apple Home app.
the app's homepage, click "+" in the
The device can be linked to Smartmi
middle of the page, then add the
Link after linking to HomeKit. Go to the
device as prompted.
Personal Info page on Smartmi Link. Tap
"HomeKit Info" and then link the HomeKit
device as prompted.
Devices linked to Smartmi Link can also
be added to HomeKit. Go to the Device
Control page on Smartmi Link. Tap "Add
to HomeKit" in "Settings" and then link
the device to HomeKit as prompted.
Note:
Please ensure that your Wi-Fi network is both
available and has Internet access. Place your
phone as close to this product as possible. (This
product does not support 5G networks).
This product will be listed as "Smartmi Air Purifier
P2" in the app's device listing.
Resetting Wi-Fi
Press and hold the
Mode Button and
Resetting Purifier
Timing Button at the
Hold down the "Switching Modes"
same time for 5s. The
and "Power on/ Standby" buttons
Wi-Fi can be reset
simultaneously for 10 seconds. After
after the purifier has
you hear a sound, the purifier has been
beeped.
reset successfully.
Turning Wi-Fi On/Off
Press and hold the
Timing Button for 5s.
The Wi-Fi can be
turned off/on after the
purifier has beeped.
07
Note:
Please ensure that your Wi-Fi network is
both available and has Internet access.Place
your phone as close to this product as possible.
(This product does not support 5G networks).
To control this accessory which is compatible
with HomeKit, it is recommended to use iOS 13.0
or a later version.
Please keep the HomeKit setup code, as you
will need to scan the code to link the device to
HomeKit after a factory reset.
iPad and iPhone are trademarks of Apple Inc.,
registered in the U.S. and other countries.
Controlling this HomeKit-enabled accessory
automatically and away from home requires a
HomePod, Apple TV, or iPad set up as a home
hub. It is recommended that you update to the
latest software and operating system.
HomeKit Setup Code
Screensaver
A screensaver animation is displayed
after 60s of no operation, and the
screensaver color reflects the air
quality. Press any button to restore to
its previous state.
Filter Replacement and Reset
Filter status reminder
Replacing and Resetting the Filter
1
Turn over the purifier and remove the filter by rotating it counterclockwise.
2
Replace the filter by following the instructions contained in the user manual.
Filter installation reminder
Note: Power off purifier and disconnect it from the power supply before performing the following operations.
No filter is detected, or the filter installed is not
certified.
Filter replacement reminder
Filters should be replaced every 6–12 months. The
app will send a reminder when the filter's lifespan
reaches 10% or less.
Once filter life drops below 10%, the Power on/
Standby button will blink every time you turn on
the machine. Please replace the filter as soon as
possible to ensure normal operation and optimal
air purification.
Reset filter
Replace the filter, and then press and hold the Mode Button for 5s with the device
turned on. The purifier will beep when the filter has successfully been reset.
How to Buy the Filter
Scan the QR Code or Visit smartmi's online store
https://www.smartmiglobal.com
for more information
Prompt:
Replace the filter in a timely manner when
prompted.
Please purchase certified compatible filters
from official channels only.
08
Publicidad
