Bosch Intuvia BUI255 Manual De Instrucciones página 14

English – 2
Fitting
Inserting and removing the battery
For inserting and removing the eBike battery in/from the
eBike, please read and observe the battery operating in-
structions.
Fitting and removing the on-board computer
(see figure A)
To fit the on-board computer (3), slide it forwards into the
holder (4).
To remove the on-board computer (3), press the locking
mechanism (14) and slide the on-board computer forwards
out of the holder (4).
Remove the on-board computer when you park the
u
eBike.
The on-board computer can be secured in place to prevent it
from being removed from the holder. To do so, remove the
holder (4) from the handlebars. Put the on-board computer
in the holder. Screw the locking screw (15) (M3 thread,
8 mm long) from below into the thread provided in the
holder. Mount the holder back onto the handlebars.
Please note: The locking screw is not designed to prevent
theft.
Operation
Prerequisites
The eBike system can only be activated when the following
requirements are met:
– A sufficiently charged battery is inserted (see battery op-
erating instructions).
– The on-board computer is properly inserted in the holder
(see "Fitting and removing the on-board computer
(see figure A)", page English – 2).
– The speed sensor is connected properly (see drive unit
operating instructions).
Switching the eBike system on/off
The following options are available for switching on the
eBike system:
– If the on-board computer is already switched on when you
insert it into the holder, the eBike system will be activated
automatically.
– Once the on-board computer and the eBike battery are
fitted, briefly press the on/off button on the on-board
computer.
– With the on-board computer inserted, push the on/off
button on the eBike battery (bicycle manufacturer-spe-
cific solutions are possible when there is no access to the
battery on/off button; see the battery operating instruc-
tions).
1 270 020 XBI | (29.11.2021)
The drive is activated as soon as you start pedalling (except
if you are using the walk assistance function or if the assist-
ance level is set to OFF). The motor output adjusts to the as-
sistance level set.
As soon as you stop pedalling when in normal operation, or
as soon as you have reached a speed of 25/45 km/h, the
eBike drive switches off the assistance. The drive is automat-
ically reactivated as soon you start pedalling again and the
speed is below 25/45 km/h.
The following options are available for switching off the
eBike system:
– Press the on/off button of the on-board computer.
– Switch off the eBike battery using its on/off button (bi-
cycle manufacturer-specific solutions are possible when
there is no access to the battery on/off button; see the bi-
cycle manufacturer operating instructions).
– Remove the on-board computer from its holder.
If no power is drawn from the eBike drive for
about 10 minutes (e.g. because the eBike is not moving) and
no button is pressed on the on-board computer or the con-
trol unit of the eBike, the eBike system will switch off auto-
matically.
eShift (optional)
eShift is the integration of electronic gear-shifting systems
into the eBike system. The eShift components are electric-
ally connected to the drive unit by the manufacturer. The
separate operating instructions describe how to operate the
electronic gear-shifting systems.
Energy supply of the on-board computer
If the on-board computer is in the holder (4), a sufficiently
charged battery is inserted in the eBike and the eBike sys-
tem is switched on, then the on-board computer is powered
by the battery of the eBike.
If the on-board computer is removed from the holder (4),
the energy is supplied via an internal battery. If the internal
battery is weak when the on-board computer is switched on,
<Attach to bike> will appear on the text indicator (d) for
3 s. The on-board computer will then turn off again.
To charge the internal battery, put the on-board computer
back in the holder (4) (when a battery is inserted in the
eBike). Switch the eBike battery on by its on/off button (see
battery operating instructions).
You can also charge the on-board computer via the USB
port. To do this, open the protective cap (8). Connect the
USB port (7) of the on-board computer via a suitable USB
cable to a standard USB charger or the USB port of a com-
puter (5 V charging voltage, max. 500 mA charging current).
<USB connected> will appear on the text indicator (d) of
the on-board computer.
Bosch eBike Systems