Rapid BNX50 Manual Del Usuario página 9

"Left hand" hook mount
Depth adjustment wheel
Single/Contact fi re switch
Tool status LED light
Battery LED indicator
(Figure 5)
(BOSCH) POWER FOR ALL ALLIANCE 18V
Battery and Logo
ASSEMBLY
REMOVAL AND CONNECTION OF THE BATTERY
Fit only the type of battery intended for use with
this tool. (see Figure 5)
To remove the battery, press the unlocking button (1)
and slide the battery out of the machine (2). (Figure
6)
To connect the battery, slide it in the other direction
until the connection clicks.
BATTERY RESIDUAL CAPACITY
This indication is made up of four red LEDs which
shows the residual capacity of the inserted battery.
(Figure 4)
The indication is turned on when a battery is inserted
into the tool, or the trigger alone is pressed. Stays on
for 5 seconds.
As the residual capacity in the battery decreases,
less and less LEDs will be turned on.
Once residual capacity is below 6% one LED will
start fl ashing.
BATTERY ERROR INDICATIONS
If an error in the battery is detected, the LEDs
will instead of residual capacity show the following
indications, and the tool will not operate. (Figure 4)
Battery error indications
Error type
Battery voltage One LED fl ashing
is critically low for 10 seconds
Battery is too All LEDs fl ashing
warm for 10 seconds
Battery not Two LEDs fl ashing
recognized for 10 seconds
LOAD NAILS INTO THE MAGAZINE
1. Press the magazine latch
magazine cover.
2. Insert nails with the tips resting against the bot-
tom of the magazine channel.
3. Close the magazine cover until it safely engages
with the magazine latch.
Note! Do not place nails of different length together
in the magazine.
REMOVE NAILS FROM THE MAGAZINE
1. Press the magazine latch
magazine cover.
2. Remove the nails from the magazine.
LED Indication
and pull out the
and pull out the
3. Close the magazine cover until it safely engages
with the magazine latch.
OPERATION
NAILING
Make sure the tool is in good working condition and
that the battery is properly connected to the tool.
There is no power switch for the tool, as soon as a
battery is connected to the tool, the tool is active and
ready to use.
The tool can be operated in two different modes,
either in single fi re mode or in contact fi re mode.
SINGLE FIRE MODE
Activate the single fi re mode by moving the switch
(Figure 3) to the left toward the one-nail symbol. The
tool is now ready for single fi ring:
1. Firmly press the safety yoke
piece until it is pushed in a few millimeters.
2. Briefl y press the trigger
3. Release the trigger and remove the tool from the
workpiece.
4. To fi re again, do steps 1 thru 3 again.
CONTACT FIRE MODE
Activate the contact fi re mode by moving the switch
(Figure 3) to the right toward the symbol with
three nails. The warning light
10 seconds and the tool is ready for contact fi ring:
1. Press the trigger
2. Firmly press the safety yoke
piece and the tool will fi re.
3. While keeping the trigger pressed release the
safety yoke from the workpiece.
4. Press the safety yoke against the next area you
want to fi re into, and the tool will fi re again.
5. To continue, repeat steps 3 and 4 continuously
and the tool will keep fi ring until the trigger is
released.
TOOL STATUS INDICATIONS
The tool is equipped with a diagnostics LED light
to indicate the current status of the tool.
Tool status LED light
Status LED indication
Tool in contact
Flashing yellow
fi re mode
No fasteners Constant
in magazine yellow
Fastener
Flashing red
jammed
Tool is
Constant red
overheated
NAIL DEPTH ADJUSTMENT
Use the depth adjustment wheel
workpiece and allow for proper setting of nail heads.
Turn the wheel left towards
into the material.
Turn the wheel right towards
of drive into the material.
FRONT LED WORK LIGHT
against the work-
and the tool will fi re.
will fl ash yellow for
and do not release it.
against the work-
Measure
Keep, or switch
to single fi re
Fill magazine
with fasteners
Remove jam-
med fastener
Wait till tool
cools down
to protect the
to drive the nail deeper
to achieve less depth
9