Makita PM001G Manual De Instrucciones página 19

Main power switch
WARNING:
Always turn o the main power
switch when not in use.
T o t u r n o n t h e m a c h i n e , p r e s s t h e m a i n p o w e r s w i t c h .
The lamps light up in green. To turn o , press and hold
the main power switch until the lamps go o .
Fig.19: 1. S p e e d i n d i c a t o r 2. M a i n p o w e r s w i t c h
The speed can be changed in three levels. To change
t h e s p e e d m o d e , p r e s s t h e m a i n p o w e r s w i t c h . W h e n
y o u c h a n g e t h e s p e e d m o d e , t h e c o r r e s p o n d i n g s p e e d
i n d i c a t o r s l i g h t u p .
NOTE: The machine employs the auto power-o
f u n c t i o n . T o a v o i d u n i n t e n t i o n a l s t a r t u p , t h e m a i n
p o w e r s w i t c h w i l l a u t o m a t i c a l l y s h u t d o w n w h e n t h e
m a c h i n e i s n o t o p e r a t e d f o r a c e r t a i n p e r i o d a f t e r t h e
m a i n p o w e r s w i t c h i s t u r n e d o n .
NOTE: I f t h e m a i n p o w e r l a m p l i g h t s u p i n r e d o r
blinks in red or green, refer to the instructions for
machine/battery protection system.
Switch action
WARNING:
Before installing the battery car-
tridge into the machine, always check to see that
the switch trigger actuates properly and returns
to the " OFF " position when released.
T o s t a r t t h e m a c h i n e , p u l l t h e s w i t c h t r i g g e r w h i l e p u l l i n g
the activation lever. The speed increases by increas-
i n g p r e s s u r e o n t h e s w i t c h t r i g g e r . R e l e a s e t h e s w i t c h
t r i g g e r t o s t o p .
Fig.20: 1. S w i t c h t r i g g e r 2. A c t i v a t i o n l e v e r
Opening and closing the levers
T h e m a c h i n e i s e q u i p p e d w i t h t h r e e l e v e r s .
Nozzle lever
The nozzle lever is used for blowing mist. Normally,
c l o s e t h e n o z z l e l e v e r , a n d o p e n t h e n o z z l e l e v e r o n l y
when blowing mist.
Fig.21: 1. C l o s e d 2. O p e n
Draining lever
T h e d r a i n i n g l e v e r i s u s e d f o r d r a i n i n g t h e l i q u i d i n t h e
t a n k . W h e n o p e r a t i n g t h e m a c h i n e , a l w a y s c l o s e t h e
l e v e r .
Fig.22: 1. C l o s e d 2. O p e n
Tank lever
The tank lever is used when replacing the filter. When
o p e r a t i n g t h e m a c h i n e , a l w a y s o p e n t h e l e v e r .
Fig.23: 1. C l o s e d 2. O p e n
Feed amount adjustment knob
You can adjust the amount of liquid fed to the end
n o z z l e . T o f e e d t h e m a x i m u m
knob so that is aligned with the triangular mark. To
feed the minimum amount of liquid, turn the knob so
t h a t " 1 " i s a l i g n e d w i t h t h e t r i a n g u l a r m a r k .
Fig.24: 1. Feed amount adjustment knob
2. T r i a n g u l a r m a r k
Electronic function
T h e m a c h i n e i s e q u i p p e d w i t h t h e e l e c t r o n i c f u n c t i o n f o r
e a s y o p e r a t i o n .
• C o n s t a n t s p e e d c o n t r o l
T h e s p e e d c o n t r o l f u n c t i o n p r o v i d e s t h e c o n s t a n t
r o t a t i o n s p e e d r e g a r d l e s s o f l o a d c o n d i t i o n s .
• F e e d v a l v e f u n c t i o n
T h e m a c h i n e i s e q u i p p e d w i t h t h e f e e d v a l v e . T h e
f e e d v a l v e a u t o m a t i c a l l y o p e n s t o f e e d t h e l i q u i d
i n t h e t a n k w h e n t h e s w i t c h t r i g g e r i s p u l l e d , a n d
i t a u t o m a t i c a l l y c l o s e s w h e n t h e s w i t c h t r i g g e r i s
r e l e a s e d .
Accidental re-start preventive
function
W h e n y o u t u r n o n t h e m a c h i n e w h i l e p u l l i n g t h e a c t i v a -
t i o n l e v e r a n d s w i t c h t r i g g e r , t h e m a c h i n e d o e s n o t s t a r t
and the main power lamp blinks in green. To start the
machine, first release the switch trigger, and then turn
o n t h e m a c h i n e .
OPERATION
CAUTION:
W hen putting on the machine, be
sure to put shoulder harness on your both shoul-
ders. O t h e r w i s e , t h e m a c h i n e m a y f a l l w h e n y o u p u t
on or use the machine, and cause an injury.
CAUTION:
W hen putting on the machine,
be sure to put on the machine on your back.
O t h e r w i s e , t h e m a c h i n e m a y f a l l d u r i n g o p e r a t i o n a n d
cause an injury.
CAUTION:
Do not place the machine on the
ground while it is running. S a n d o r d u s t m a y e n t e r
f r o m s u c t i o n i n l e t a n d c a u s e a m a l f u n c t i o n o r p e r -
sonal injury.
Before operating the machine, adjust the length of the
shoulder harness and the waist belt.
1.
Place the machine on a flat and stable surface.
2.
M a k e s u r e t h a t t h e l e v e r s a r e i n t h e f o l l o w i n g
p o s i t i o n s .
• T h e d r a i n i n g l e v e r i s i n t h e c l o s e d p o s i t i o n .
Fig.25: 1. D r a i n i n g l e v e r
• T h e t a n k l e v e r i s i n t h e o p e n p o s i t i o n .
Fig.26: 1. T a n k l e v e r
• T h e n o z z l e l e v e r i s i n t h e c l o s e d p o s i t i o n .
Fig.27: 1. N o z z l e l e v e r
19 ENGLISH
a m o u n t o f l i q u i d , t u r n t h e