Publicidad
Idiomas disponibles
Idiomas disponibles
ML-3500MS AC/DC MODELS
FOR AC OPERATION
1. Align the top notch of the 7-pin plug on the AC cord to the notch in the ballast outlet; turn the
locking ring to the right over the plug to secure.
2. Press ON the BLACK ballast rocker switch.
3. Press ON the RED Inverter rocker switch.
FOR DC OPERATION
1. Connect the 12-volt plug to the Spectroline
supply. The BP-12A must be fully charged before using! Refer to the BP-12A operating
instructions for full information.
2. Insert the plug into the receptacle on the battery pack.
3. Align the top notch of the 7-pin plug on the DC cord to the notch in the ballast outlet; turn the
locking ring to the right over the plug to secure.
4. Press ON the BLACK ballast rocker switch.
5. Press ON the RED Inverter rocker switch.
NOTE: The BP-12A battery pack includes a 12-volt battery, 120V/60Hz-charger, the BP-12A/F
has a 230V/50Hz charger, the BP-12A/FA has a 240V/50Hz charger and the BP-12A/J has a
100V/50-60Hz charger. All battery packs include a nylon carrying case. IMPORTANT: Disconnect
lamp cord plug from battery pack when the unit is not in use.
ELECTRICAL SPECIFICATIONS—ML-3500MS AC/DC MODELS
MAXIMA Model
ML-3500MS
ML-3500MS/F
120V/60Hz/
Power Source
1.00A
BP-12A
12VDC
Power Source
OPERATOR SERVICING
The following instructions are intended for limited servicing of the lamp. Do not perform
any servicing that is not covered in these instructions. Return the lamp to the factory for
maintenance not covered in this section.
HOUSING AND FILTER MAINTENANCE
CAUTION: Always shut off the switch on the ballast and unplug the ballast from the power
outlet before performing any maintenance or servicing. Allow the lamp to cool before
handling.
Clean the lamp and ballast housings with water and a mild detergent and wipe dry. Periodically
clean the filter with a glass cleaner and a soft cloth.
FILTER REPLACEMENT
The lamp is shipped with a 2F958 filter lens. This may be used with either the
BLE-35RA spot bulb or the BLE-35RAF flood bulb. The 2F350 filter lens may be ordered with
a BLE-35RA spot bulb (only) to produce a more diffused spot beam
that is not as wide as the flood beam.
1. Peel the silicone-rubber filter holder from around the circumference of the lamp housing. The
filter will remain inside the filter holder.
2. Press the existing filter out of the filter holder.
3. Press the new filter gently but firmly into the filter holder.
4. Reattach the filter holder by pressing it around the circumference of the lamp housing with the
heel of your hand. Be sure the groove in the filter holder seats over the rim of the housing.
BP-12A 12-volt battery pack or to a suitable DC
®
ML-3500MS/FA
ML-3500MS/J
230V/50Hz/
240V/50Hz/
100V/50-60Hz/
0.75A
0.75A
1.00A
12VDC
12VDC
12VDC
4
BULB REPLACEMENT
Use only a Spectroline UV bulb/reflector assembly. Using any other bulb may damage the
unit and will void the warranty. The lamp is shipped with a BLE-35RA spot bulb/reflector
assembly as standard. The lamp may be ordered with a BLE-35RAF flood bulb/reflector
assembly.
1. Remove the filter holder.
2. Insert the bulb/reflector tool in the two holes in the old bulb/reflector, rotate counterclockwise
and pull.
3. Hold the new bulb/reflector by its protective cover while inserting it into the socket with a
clockwise quarter-turn bayonet action. Firm pressure is needed to overcome the spring in the
socket. Pop off the black fasteners and remove the protective cover.
4. Reattach the filter holder.
UV INTENSITY VERIFICATION
To ensure that your MAXIMA™ ML-3500 is operating at the required UV intensity, it should
be checked periodically. The AccuMAX
TM
wavelength UV-A/VIS sensor detector to accurately measure ultraviolet irradiance or visible
light. The AccuMAX XR-1000 digital readout unit with the XS-365 UV sensor or the Spectroline
DM-365XA digital readout unit are also recommended for accurate UV-A measurement. The
meters are specially designed to measure the UV irradiance from 320–400nm with a peak at
365nm.
For more information about these units, please contact the Customer Service Department at
Spectro-UV. Call toll-free 1-866-230-7305.
ENVIRONMENTAL CONDITIONS
These UV lamps are designed to be safe under the following conditions:
• Indoor use
• Altitude up to 2,000 m (6,562 ft)
• Temperature 5°C to 40°C (41°F to 104°F)
• Maximum relative humidity 80% for temperatures up to 31°C (88°F) decreasing linearly to 50%
relative humidity at 40°C (104°F)
• Mains supply voltage fluctuations not to exceed ±10% of the nominal voltage
• Installation Category II
• Pollution Degree 2
LIMITED WARRANTY
The warranty policy for these UV lamps is provided on the Certificate of Limited Warranty enclosed
separately with each unit.
NOTE: Please contact the Customer Service Department at Spectro-UV for assistance. Have the
model and serial numbers of the unit and the date of purchase available when calling.
XRP-3000 radiometer/photometer kit uses a dual-
5
Publicidad
