Kärcher VC 6 Cordless ourFamily Manual De Instrucciones página 13

** LED crevice nozzle
28
** Extension hose
29
** Flexible crevice nozzle
30
** Removable battery (2x)
31
** Soft brush
32
** Free-standing parking station
33
** Soft motorized brush (hard floor nozzle)
34
* EN 1822:1998
** optional
Installing the wall bracket/free-
standing parking station with
charging function
The scope of delivery includes either a wall bracket or a
free-standing parking station with charging function for
correct storage of the vacuum cleaner and accessories.
● Installing the wall bracket
Note
Mount the wall bracket at a suitable point using the
screws and dowels supplied.
For safe storage of the device, the lower screw fasten-
ing of the wall bracket should be placed at a distance of
0.83-0.85 m from the floor.
Illustration F
ATTENTION
Material damage due to incorrect installation
Incorrect installation can damage both the device and
the floor covering if it falls.
Use suitable mounting tools for wall mounting.
Take the weight of the device and the loading capacity
of the installation location into account when selecting
the fasteners.
WARNING
Risk of electric shock and injuries
Make sure there are no electrical cables, water or gas
pipes in the wall around the mounting area.
● Installing the free-standing parking station
Note
Installation on the wall is not necessary.
1 Assemble the base, connecting tube and bracket so
that they audibly click into place.
2 Place the unit in the support.
Illustration G
ATTENTION
Risk of injury or damage to property
If the parking station is placed in an unfavourable posi-
tion (e.g. in the middle of a room), this constitutes a trip-
ping hazard and may result in injury and/or it can fall
over and damage the unit.
Place the unit with the parking station in a safe, quiet
place (e.g. wall, corner).
Note
Removal is carried out by pressing the unlocking but-
tons on the rear side of the parking station on the base
and support.
Initial startup
Installing accessories
Note
The multi-function brush is also driven by its own inte-
grated motor and must therefore always be connected
directly to the hand-held device or the suction pipe in or-
der to ensure the power supply.
All other accessor parts can also be used directly with
the hand-held device or with the suction pipe to increase
the reach.
 Push the suction pipe on to the suction fitting of the
dust container until it audibly clicks into place.
 Press the unlocking button and remove the suction
pipe from the suction fitting.
Illustration B
 Push the floor nozzle on to the suction pipe until it
audibly clicks into place.
 Press the unlocking button and remove the floor
nozzle from the suction pipe.
Illustration C
 Push accessory, such as the crevice nozzle, on to
the suction fitting of the dust container or suction
pipe until it audibly clicks into place.
Illustration D
Inserting the battery
ATTENTION
Dirty contacts
Damage to the device and battery
Check the battery mount and the contacts for soiling
and clean them as necessary before inserting the bat-
tery.
Note
Use only fully charged batteries.
1. Push the battery into the mounting in the device until
it audibly latches into place.
Illustration E
Note
The device is not supplied with a charged battery. Fully
charge the battery before using it for the first time.
Please observe the enclosed safety instructions for bat-
tery powered vacuum cleaners.
Note
The battery can be charged with the device or separate-
ly (e.g. for variants with an additional battery).
Note
For a detailed description of the LED displays, see
chapter LED display
1. Charge the battery with the device.
 To charge the device, attach it to the wall bracket
with charging function included in the scope of
delivery.
Illustration F
2. Charge the battery separately.
 Place the battery on a flat and safe surface to
charge it.
ATTENTION
Material damage due to incorrect battery storage
Incorrect storage during charging can result in the bat-
tery e.g. falling down or damaging heat-sensitive surfac-
es.
Make sure charging of the separate battery takes place
on a flat, smooth and heat-insensitive surface.
Furthermore, the battery should not be covered with ob-
jects (e.g. fabrics or papers) while it is being charged.
3. Plug the charger into a socket.
Insert the connecting plug into the charging socket
of the wall bracket / battery.
English
Battery charging
13