Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
(Original instructions)
♦ Fit the base on the main body of the appliance.
♦ Fix the base using the floor bracket
♦ Stand the appliance up again so as to check that the
base works properly.
Assembling the castors:
♦ To assemble the castors, place the appliance face down
♦ Insert the 4 castors (13) in the four holes
♦ Stand the appliance up again so as to check that the
castors work properly.
Assembling the grill and the propeller (FIG
1&2):
♦ A) remove the fan blade bracket (4) and the guard brack-
et (6) on the fan head,
♦ B) align the rear fan guard (7) to the card position and
install it, tighten the guard bracket (6) clockwise, and fix
the rear fan guard,
♦ C) Install the fan blade propeller (5) against the motor
shaft, pay attention to the motor shaft pin should be
aligned with the slot on the fan blade, and tighten the fan
blade bracket (4) on the motor shaft counterclockwise.
♦ D) install the guard bracket (1) on the rear fan guard (7),
and then install the front fan guard (3) (the mist vent (2)
on the front fan guard faces down), it is best to tighten
the fan guard screws
INSTRUCTIONS FOR USE
Before use:
♦ Make sure that all products' packaging has been
removed.
♦ Prepare the appliance according to the function you wish
to use:
Use:
♦ CAUTION: Care should be taken to avoid spillage when
moving the appliance.
♦ Extend the cable completely before plugging it in.
♦ Connect the appliance to the mains.
♦ Guide the appliance to direct the flow of air in the desired
direction.
♦ Turn the appliance on, by using the on/off button.
♦ Select the appliance function desired.
♦ Select the desired power.
♦ Select the desired speed.
8
Fan function:
♦ Select the fan function.
♦ Select the desired fan speed.
Timer function:
♦ The appliance's operating time can be controlled.
♦ To program the operating time simply select it using the
(S) or (1.3) buttons.
♦ You can select between 1 and 12 hours
♦ If you press the "Timer" button when the fan is on, the
display will then show the time remaining
♦ The time programmed or remaining time will appear on
the display (A).
♦ After the selected time the appliance will switch off
automatically.
Oscillation function:
♦ The oscillation function makes it possible to direct the
flow from the apparatus so that it automatically alter-
nates over a range of 75º.
♦ To activate this function, press the oscillation on/off
button (R) or (1.6).
♦ To deactivate this function, press the oscillation on / off
button (R ) or (1.6) again.
♦ MODES
♦ Press the "Wind Mode" (P) or (1.4) button to set the wind
mode (normal, sleep, natural).
♦ The Normal Mode is set by default when the unit is first
turned on
♦ The Natural mode creates variable wind patterns so as
to simulate the variable winds
♦ that you would experience outdoors
♦ The Sleep mode creates wind patterns that are the same
as the Natural Mode wind.
♦ patterns. However, when the fan is set to either Medium
or High Speed, the pattern will drop a speed level after
approximately 30 minutes.
♦ Cooling using ultrasonic mist.
♦ Press the "M" settings button to switch the ultrasonic
mist on, and you can select the mist volume (low, middle
and high) by pressing the button several times.
Once you have finished using the appli-
ance:
♦ Turn the appliance off, using the on/off switch (O).
♦ Unplug the appliance from the mains.
♦ Put the cable back in the cable housing.
♦ Clean the appliance.
Publicidad
